Toyota CH-R Service Manual: Operation Check

OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this inspection with the customize parameters at the initial settings.

HINT:

Perform this inspection with the door switch of the map light assembly on.

Lights Controlled by Illuminated Entry System

Control

Condition

Lights that Operate

Actuation Area-linked*1

With the engine switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map Light Assembly
  • No. 1 Room Light Assembly

Door Lock/Unlock-linked

With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.

  • Map Light Assembly
  • No. 1 Room Light Assembly
  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3
  • Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3

Door Open/Close-linked

With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.

  • Map Light Assembly
  • No. 1 Room Light Assembly
  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3
  • Instrument Cluster FinishPanel Garnish (Cup Holder Illumination Light)*3

With the engine switch off and all of the doors closed, open either front door and check that the light that operates turns on. While the light that operates is on, close all of the doors and check that the light that operates turns off after approximately 40 seconds*1.

Engine Switch Illumination*1

With the ignition switch ACC or ON, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.

  • Map Light Assembly
  • No. 1 Room Light Assembly

Engine Switch-linked*1

Turn the engine switch from on (ACC) or on (IG) to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map Light Assembly
  • No. 1 Room Light Assembly
  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3
  • Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3

Ignition Switch-linked*2

Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map Light Assembly
  • No. 1 Room Light Assembly
  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3
  • Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3

Shift position-linked*3

With the ignition switch turned to ACC or ON, move the shift lever from P to any position and check that the lights dim. While the lights are dim, move the shift lever to P and check that the lights return to full brightness.

  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)
  • Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)
  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: w/ Door Ambient Illumination Light

INSPECT BATTERY SAVING CONTROL OPERATION

(a) The operations and conditions of this control are described below.

Control

Condition

Lights that Operate

Basic operation

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is turned to ACC or ON.
  • Any door is opened and closed.
  • The luggage compartment door is opened and closed.
  • Any door is unlocked.
  • The key enters any exterior actuation area.
  • Map Light Assembly
  • No. 1 Room Light Assembly
  • Engine Switch Illumination*1
  • No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2
  • Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2

Interior light auto cut operation

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is turned to ACC or ON.
  • Map Light Assembly
  • No. 1 Room Light Assembly
  • No. 1 Luggage Compartment Light Assembly
  • Vanity Light Assembly
  • *1: w/ Smart Key System
  • *2: w/ Door Ambient Illumination Light
    System Description
    SYSTEM DESCRIPTION ILLUMINATED ENTRY SYSTEM (a) The illuminated entry system has the following control functions: Control Outline Lights that Operate ...

    Customize Parameters
    CUSTOMIZE PARAMETERS PROCEDURE 1. CUSTOMIZE LIGHTING SYSTEM (INT) (a) Customizing using the Techstream HINT: The following items can be customized. NOTICE: When the customer requests a ...

    Other materials:

    Toyota CH-R Owners Manual > Driving procedures: Turn signal lever
    Operating instructions Right turn Lane change to the right (move the lever partway and release it) The right hand signals will flash 3 times. Lane change to the left (move the lever partway and release it) The left hand signals will flash 3 times. Left turn ■Turn signals can b ...

    Toyota CH-R Service Manual > Navigation System: Mute Signal Circuit between Radio Receiver and Telematics Transceiver
    DESCRIPTION The telematics transceiver sends a mute signal to the radio and display receiver assembly. The radio and display receiver assembly controls the volume according to the mute signal from the telematics transceiver. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Depending on the ...

    © 2017-2019 Copyright www.tochr.net
    0.0147