Toyota CH-R Service Manual: Data List / Active Test

Toyota CH-R Service Manual / Networking / Lin Communication System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Main Body or Smart Key (w/ Smart Key System) / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Communication D-Door Motor	Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU)	OK or STOP	OK: Connected STOP: Not Connected	DTC is output if an error occurs in LIN communication.
Communication P-Door Motor	Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU)	OK or STOP	OK: Connected STOP: Not Connected	DTC is output if an error occurs in LIN communication.
Communication RR-Door Motor	Connection status between power window regulator motor assembly (for rear RH door) and main body ECU (multiplex network body ECU)	OK or STOP	OK: Connected STOP: Not Connected	DTC is output if an error occurs in LIN communication.
Communication RL-Door Motor	Connection status between power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU)	OK or STOP	OK: Connected STOP: Not Connected	DTC is output if an error occurs in LIN communication.
Communication Master SW	Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU)	OK or STOP	OK: Connected STOP: Not Connected	DTC is output if an error occurs in LIN communication.
The Number of DTC	Number of DTCs	0 to 255	Number of stored DTCs	-

Body Electrical > Smart Key > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
# Codes	Number of DTCs	0 to 255	Number of stored DTCs	-

Diagnosis System

DIAGNOSIS SYSTEM DESCRIPTION The main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) control the LIN communication system. LIN communication system data and ...

Dtc Check / Clear

DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main Body or S ...

Other materials:

Toyota CH-R Service Manual > Can Communication System: Combination Meter ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Combination Meter ECU Communication Stop Mode Any of the following conditions are met: Communication stop for "Combination Meter" is indicated on the "Comm ...

Toyota CH-R Owners Manual > Child restraint systems: Using an anchor bracket (for top tether strap)
■ Anchor brackets (for top tether strap) Anchor brackets are provided for each rear seat. Use anchor brackets when fixing the top tether strap. ■ Fixing the top tether strap to the anchor bracket Install the child restraint system in accordance to the operation manual enclosed with the ...

Toyota CH-R Service Manual: Data List / Active Test

Diagnosis System

Dtc Check / Clear

Other materials:

Toyota C-HR (AX20) 2023-2026 Owner's Manual

Toyota CH-R Owners Manual

Toyota CH-R Service Manual