Toyota CH-R Service Manual: SM Solenoid Circuit (C1225-C1228,C1468,C1469,C146A,C146B)

Toyota CH-R Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System / SM Solenoid Circuit (C1225-C1228,C1468,C1469,C146A,C146B)

DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1225

SM Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C1226

SA2 Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C1227

SA3 Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C1228

STR Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C1468

SFR Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C1469

SFL Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C146A

SRR Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

C146B

SRL Solenoid Circuit

Solenoid valve signal does not match the check result.
  • Solenoid circuit
  • Solenoid valve (brake actuator assembly)

WIRING DIAGRAM

Refer to DTC C146E.

Click here

PROCEDURE

1.

RECONFIRM DTC

HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).

(a) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(b) Turn the ignition switch off.

(c) Start the engine.

(d) Drive the vehicle at a speed of 20 km/h (12 mph) or more.

(e) Check if the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result

Proceed to

DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B are not output.

A

DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and/or C146B are output.

B

HINT:

  • The skid control ECU (brake actuator assembly) performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.
  • If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).
  • If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
  • If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.
A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY

    Open in ABS Motor Relay Circuit (C146C)
    DESCRIPTION The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU turns the ABS motor relay on to operate the pump motor. If the voltage supplied t ...

    Yaw Rate Sensor (C1234,C1472,C1474)
    DESCRIPTION The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication. HINT: If there is a malfuncti ...

    Other materials:

    Toyota CH-R Service Manual > Black Out Tape(for Rear Door): Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the black out tape removal/installation are shown below. Necessary Procedure After Parts Removed ...

    Toyota CH-R Service Manual > Wheel Opening Moulding(for Rear): Reassembly
    REASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL NO. 1 BODY OUTSIDE MOULDING PAD HINT: When installing the No. 1 body outside moulding pad, heat the quarter outside ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0086