DESCRIPTION
This DTC is stored when the blind spot monitor sensor RH (Slave) detects a short to +B in the outer rear view mirror indicator RH.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AB1 |
Short to +B in Outer Mirror Indicator(Slave) |
Both of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When checking for DTCs, make sure that the blind spot monitor system is turned on.
PROCEDURE
|
1. |
CHECK DTC |
(a) Turn the ignition switch off.
(b) Turn the ignition switch to ON.
(c) Recheck for DTCs and check if the same DTC is output again.
Body Electrical > Blind Spot Monitor Slave > Trouble CodesOK:
No DTCs are output.
| OK | |
USE SIMULATION METHOD TO CHECK
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT) |
|
*a |
Front view of wire harness connector (to blind spot monitor sensor RH (Slave)) |
(a) Disconnect the blind spot monitor sensor RH (Slave) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
M63-4 (OMIR) - Body ground |
Ignition switch to ON |
Below 1 V |
| OK | |
REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE) |
|
|
3. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT) |
|
*a |
Front view of wire harness connector (to blind spot monitor sensor RH (Slave)) |
(a) Disconnect the IND2 outer mirror RH connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
M63-4 (OMIR) - Body ground |
Ignition switch to ON |
Below 1 V |
| OK | |
REPLACE OUTER MIRROR RH |
|
|
4. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT) |
|
*a |
Front view of wire harness connector (to blind spot monitor sensor RH (Slave)) |
(a) Disconnect the I8 outer rear view mirror assembly RH connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
M63-4 (OMIR) - Body ground |
Ignition switch to ON |
Below 1 V |
| OK | |
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH |
| NG | |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
Short to GND in Outer Mirror Indicator(Slave) (C1AB3)
Short to GND in Outer Mirror Indicator(Master) (C1AB2)Toyota CH-R Service Manual > Occupant Classification Ecu: Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed, installed, or replaced during the
occupant detection ECU removal/installation are shown below.
Necessary Procedure After Parts Re ...
Toyota CH-R Service Manual > Smart Key System(for Entry Function): New Key cannot be Registered
DESCRIPTION
If a new electrical key transmitter sub-assembly could not be registered, wave
interference or a malfunction of the certification ECU (smart key ECU assembly),
electrical key transmitter sub-assembly, ID code box (immobiliser code ECU), steering
lock ECU (steering lock actuator or ...