Toyota CH-R Service Manual: Short to GND in Outer Mirror Indicator(Slave) (C1AB3)

Toyota CH-R Service Manual / Park Assist / Monitoring / Blind Spot Monitor System / Short to GND in Outer Mirror Indicator(Slave) (C1AB3)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (Slave) detects a short to ground in the outer rear view mirror indicator RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AB3

Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
  • The blind spot monitor system is on
  • The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time
  • Outer mirror RH
  • Outer rear view mirror assembly RH
  • Wire harness or connector
  • Blind spot monitor sensor RH (Slave)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.

PROCEDURE

1.

CHECK DTC

(a) Turn the ignition switch off.

(b) Turn the ignition switch to ON.

(c) Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - OUTER REAR VIEW MIRROR ASSEMBLY RH)

(a) Disconnect the M63 blind spot monitor sensor RH (Slave) connector.

(b) Disconnect the I8 outer rear view mirror assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M63-4 (OMIR) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

(a) Disconnect the IND2 outer mirror RH connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I8-12 (BSR+) - Body ground

Always

10 kΩ or higher
NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

4.

INSPECT OUTER MIRROR RH

(a) Remove the outer mirror RH.

Click here

(b) Inspect the outer rear view mirror indicator RH on the outer mirror RH.

Click here

OK

REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)

NG

REPLACE OUTER MIRROR RH

    Open in Outer Mirror Indicator(Master) (C1AB4)
    DESCRIPTION This DTC is stored when the blind spot monitor sensor LH (Master) detects an open in the outer rear view mirror indicator LH. DTC No. Detection Item DT ...

    Short to +B in Outer Mirror Indicator(Slave) (C1AB1)
    DESCRIPTION This DTC is stored when the blind spot monitor sensor RH (Slave) detects a short to +B in the outer rear view mirror indicator RH. DTC No. Detection Item ...

    Other materials:

    Toyota CH-R Service Manual > Rocker Panel Moulding: Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL ROCKER PANEL MOULDING (a) Engage the clips to install the rocker panel moulding as shown in the illustration. ...

    Toyota CH-R Service Manual > Shift Lever: Installation
    INSTALLATION PROCEDURE 1. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY (a) Temporarily install the floor shift shift lever assembly to the body with the 4 bolts. (b) Fully tighten the 4 bolts in the order shown in the illustration. Torque: 12 N·m {122 kgf·cm, 9 ft·lbf} (c) Engage the 6 cl ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0089