Toyota CH-R Service Manual: Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter

Toyota CH-R Service Manual / Audio / Video / Audio And Visual System(for Radio And Display Type) / Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter

DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

(a) Disconnect the F129 radio and display receiver assembly connector.

(b) Disconnect the j1 No. 1 stereo jack adapter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F129-14 (ADPG) - j1-9 (AUXO)

Always

Below 1 Ω

F129-10 (AGND) - j1-10 (AGND)

Always

Below 1 Ω

F129-12 (VAR+) - j1-6 (ARO)

Always

Below 1 Ω

F129-11 (VAL+) - j1-7 (ALO)

Always

Below 1 Ω

F129-13 (VA-) - j1-8 (ASGN)

Always

Below 1 Ω

F129-14 (ADPG) - Body ground

Always

10 kΩ or higher

F129-10 (AGND) - Body ground

Always

10 kΩ or higher

F129-12 (VAR+) - Body ground

Always

10 kΩ or higher

F129-11 (VAL+) - Body ground

Always

10 kΩ or higher

F129-13 (VA-) - Body ground

Always

10 kΩ or higher

*a

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

*b

Front view of wire harness connector

(to No. 1 Stereo Jack Adapter Assembly)

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

    Speaker Circuit
    DESCRIPTION If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers. Thus sound cannot be heard from the speakers even if ther ...

    Data Signal Circuit between Radio Receiver and Stereo Jack Adapter
    DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit. WIRING DIAGRAM ...

    Other materials:

    Toyota CH-R Service Manual > Airbag System: Short in Driver Side Knee Airbag Squib Circuit (B1860/64-B1863/64)
    DESCRIPTION The driver side knee airbag squib circuit consists of the airbag sensor assembly and lower No. 1 instrument panel airbag assembly. The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. These DTCs are stored when a malfunction is dete ...

    Toyota CH-R Service Manual > Brake Booster: Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY (a) Remove the brake vacuum check valve assembly from the brake booster assembly. (b) Remove the check valve grommet from the brake booster assembly. 2. REMOVE VACUUM WARNING SWITCH ASSEMBLY (a) Remove the vacuum warning switc ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    KIA Niro EV / Hybrid (SG2) - (2021-2023) - Owner's manual

    © 2017-2023 Copyright www.tochr.net
    0.0129