Toyota CH-R Service Manual: Installation

Toyota CH-R Service Manual / Supplemental Restraint Systems / Rear Airbag Sensor / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL NO. 2 SIDE AIRBAG SENSOR

(a) Check that the ignition switch off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

*a

Correct

*b

Incorrect

(d) Connect the connector to the No. 2 side airbag sensor.

*a

White Housing Lock

*b

Connect

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

  • Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
  • When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.

(e) Engage the claw to install the No. 2 side airbag sensor with the bolt.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

  • If the No. 2 side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  • When installing the No. 2 side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
  • Make sure that the No. 2 side airbag sensor claw is securely inserted into the body hole.

(f) Check that there is no looseness in the installed parts of the No. 2 side airbag sensor.

2. INSTALL REAR SEAT SIDE GARNISH (w/ Rear Seat Side Airbag)

Click here

3. INSTALL REAR SEAT SIDE GARNISH (w/o Rear Seat Side Airbag)

Click here

4. INSTALL REAR PILLAR COVER (w/ Rear Seat Side Airbag)

Click here

5. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY

Click here

6. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

7. INSTALL REAR DOOR SCUFF PLATE (w/ Rear Seat Side Airbag)

Click here

8. INSTALL REAR DOOR SCUFF PLATE (w/o Rear Seat Side Airbag)

Click here

9. INSTALL REAR SEAT ASSEMBLY

Click here

10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

11. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here

12. INSPECT SRS WARNING LIGHT

Click here

    On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the No. 2 side airbag sensors. PROCEDURE 1. INSPECT NO. 2 SIDE AIR ...

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during th ...

    Other materials:

    Toyota CH-R Service Manual > Lighting (ext): High Mounted Stop Light Assembly
    Components COMPONENTS ILLUSTRATION *1 CENTER STOP LIGHT ASSEMBLY *2 NO. 2 REAR SPOILER COVER Removal REMOVAL PROCEDURE 1. REMOVE REAR SPOILER ASSEMBLY Click here 2. REMOVE NO. 2 REAR SPOILER COVER Click here 3. REMOVE CENT ...

    Toyota CH-R Service Manual > Wheel Opening Moulding(for Rear): Components
    COMPONENTS ILLUSTRATION *1 QUARTER OUTSIDE MOULDING - - ILLUSTRATION *1 NO. 1 BODY OUTSIDE MOULDING PAD - - ● Non-reusable part - - ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.011