REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 side airbag sensor removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure |
Necessary Procedures |
Effects / Inoperative when not performed |
Link |
---|---|---|---|
Disconnect cable from negative battery terminal |
Initialize back door lock |
Power door lock control system |
|
Memorize steering angle neutral point |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
HINT:
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
CAUTION:
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE REAR SEAT ASSEMBLY
Click here
4. REMOVE REAR DOOR SCUFF PLATE (w/ Rear Seat Side Airbag)
Click here
5. REMOVE REAR DOOR SCUFF PLATE (w/o Rear Seat Side Airbag)
Click here
6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.
7. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY
Click here
8. REMOVE REAR PILLAR COVER (w/ Rear Seat Side Airbag)
Click here
9. REMOVE REAR SEAT SIDE GARNISH (w/ Rear Seat Side Airbag)
Click here
10. REMOVE REAR SEAT SIDE GARNISH (w/o Rear Seat Side Airbag)
Click here
11. REMOVE NO. 2 SIDE AIRBAG SENSOR
(a) Check that the ignition switch off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Remove the bolt and disengage the claw to separate the No. 2 side airbag sensor. |
|
(d) Disconnect the connector to remove the No. 2 side airbag sensor.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
*a |
White Housing Lock |
*b |
Yellow CPA |
*c |
Slide |
*d |
Push |
(2) Push down the white housing lock again and disconnect the connector.
NOTICE:
Do not push down the part (A) shown in the illustration when disconnecting the connector.
(e) After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.
*a |
Correct |
*b |
Incorrect |
Toyota CH-R Service Manual > Rocker Panel Moulding: Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR WHEEL HOUSE FRONT PLATE
Click here
2. REMOVE ROCKER PANEL MOULDING
(a) Apply protective tape around the rocker ...
Toyota CH-R Service Manual > Vehicle Stability Control System: Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting a vehicle with a diagnosis system, the only difference from
the usual troubleshooting procedure is connecting the Techstream to the vehicle
and reading various data output from the skid control ECU (brake actuator assembly).
The skid control E ...