Toyota CH-R Service Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter, Main Body, Occupant Detection or SRS Airbag / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

2nd-Row Seatbelt Buckle (R)

Rear RH seat belt buckle switch signal

ON or OFF

OFF: Rear RH seat belt fastened

ON: Rear RH seat belt not fastened

-

2nd-Row Seatbelt Buckle (L)

Rear LH seat belt buckle switch signal

ON or OFF

OFF: Rear LH seat belt fastened

ON: Rear LH seat belt not fastened

-

2nd-Row Seatbelt Buckle (C)

Rear center seat belt buckle switch signal

ON or OFF

OFF: Rear center seat belt fastened

ON: Rear center seat belt not fastened

-

Driver Side Seatbelt Warning Buzzer

Driver seat belt warning buzzer

ON or OFF

Customize setting displayed

-

P-Seatbelt Warning Buzzer

Front passenger seat belt warning buzzer

ON or OFF

Customize setting displayed

-

Rear Seatbelt Warning Buzzer

Rear seat belt warning buzzer

ON or OFF

Customize setting displayed

-

Body Electrical > Occupant Detection > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Passenger Buckle SW

Front passenger buckle switch

Unset, Set or NG

Unset: Seat belt not fastened

Set: Seat belt fastened

NG: Data is not determined

-

Body Electrical > SRS Airbag > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Left side Buckle SW

LH buckle switch

Unset, Set or NG

Unset: Seat belt not fastened

Set: Seat belt fastened

NG: Data is not determined

-

Right side Buckle SW

RH buckle switch

Unset, Set or NG

Unset: Seat belt not fastened

Set: Seat belt fastened

NG: Data is not determined

-

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RR Door Courtesy SW

Rear door courtesy light switch RH

ON or OFF

ON: Rear door RH open

OFF: Rear door RH closed

-

RL Door Courtesy SW

Rear door courtesy light switch LH

ON or OFF

ON: Rear door LH open

OFF: Rear door LH closed

-

D Seat Buckle SW

Driver seat belt buckle switch

ON or OFF

ON: Driver seat belt unfastened

OFF: Driver seat belt fastened

-

ACTIVE TEST

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Driver Side Seat Belt

Front seat belt warning light

ON or OFF

-

Rear Seat Belt

Rear seat belt warning light

ON or OFF

-

    Terminals Of Ecu
    TERMINALS OF ECU CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY *A Main Body ECU (Multiplex Network Body ECU) with 1 Connecto ...

    On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DRIVER SEAT BELT WARNING LIGHT HINT: The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger ...

    Other materials:

    Toyota CH-R Service Manual > Headlight Dimmer Switch: Installation
    INSTALLATION PROCEDURE 1. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY (a) Engage the claws to install the headlight dimmer switch assembly as shown in the illustration. Install in this Direction (b) Connect the connector. 2. INSTALL WINDSHIELD WIPER SWITCH ASSEMBL ...

    Toyota CH-R Service Manual > Power Window Control System: Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH
    DESCRIPTION If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode. If power window initialization has not been performed, the auto up and down functions will not operate. Click here WIRING ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2024 Copyright www.tochr.net
    0.009