Toyota CH-R Service Manual: Removal

Toyota CH-R Service Manual / Seat Belt / Front Seat Outer Belt Assembly / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Initialize back door lock

Power door lock control system

Memorize steering angle neutral point

Memorize steering angle neutral point

Pre-collision system

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • If an SRS part is accidentally deployed, it may cause a serious injury.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Click here

4. REMOVE FRONT DOOR SCUFF PLATE

Click here

5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the front door opening trim weatherstrip.

6. REMOVE REAR DOOR SCUFF PLATE (w/o Rear Seat Side Airbag)

Click here

7. REMOVE REAR DOOR SCUFF PLATE (w/ Rear Seat Side Airbag)

Click here

8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the rear door opening trim weatherstrip.

9. REMOVE LAP BELT OUTER ANCHOR COVER

(a) Disengage the claws and guide to remove the lap belt outer anchor cover as shown in the illustration.

Remove in this Direction

10. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.

11. REMOVE CENTER PILLAR LOWER GARNISH

Click here

12. REMOVE CENTER PILLAR GARNISH ASSEMBLY

Click here

13. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the nut to disconnect the shoulder anchor of the front seat outer belt assembly.

(b) Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

*a

Protective Tape

*b

Locking Button

(c) for Front Passenger Seat Belt with Selectable Force Limiter:

(1) Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the selectable force limiter connector as shown in the illustration.

*a

Protective Tape

*b

Locking Button

(d) Remove the bolt.

(e) Disengage the guides to remove the front seat outer belt assembly.

14. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.

    On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the front seat outer belt assembly. PROCEDURE 1. INSPECT FRONT SEA ...

    Inspection
    INSPECTION PROCEDURE 1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY *a Retractor *b Unlock *c Lock *d ...

    Other materials:

    Toyota CH-R Owners Manual > Dynamic radar cruise control with full-speed range: Changing the vehicle-to-vehicle distance (vehicle-to-vehicle distance control mode)
    Pressing the switch changes the vehicle-to-vehicle distance as follows: Long Medium Short The vehicle-to-vehicle distance is set automatically to long mode when the engine switch is turned to the "ON" position (vehicles without a smart key system) or IGNITION ON mode (vehicl ...

    Toyota CH-R Service Manual > Park / Neutral Position Switch: Inspection
    INSPECTION PROCEDURE 1. INSPECT PARK/NEUTRAL POSITION SWITCH *a Component without harness connected (Park/Neutral Position Switch) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.012