Toyota CH-R Service Manual: Inspection

Toyota CH-R Service Manual / Window / Glass / Power Window Regulator Motor(for Rear Door) / Inspection

INSPECTION

CAUTION / NOTICE / HINT

NOTICE:

  • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.
  • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly.

    Click here

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

(a) Connect a positive (+) battery lead to connector terminal 2 (B).

NOTICE:

Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

*a

Component without harness connected

(Power Window Regulator Motor Assembly LH)

*b

Clockwise

*c

Counterclockwise

*d

Motor Gear

(b) Connect a negative (-) battery lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

Motor gear rotates clockwise
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

Motor gear rotates counterclockwise
  • If the result is not as specified, replace the power window regulator motor assembly LH.

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

(a) Connect a positive (+) battery lead to connector terminal 2 (B).

NOTICE:

Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

*a

Component without harness connected

(Power Window Regulator Motor Assembly RH)

*b

Clockwise

*c

Counterclockwise

*d

Motor Gear

(b) Connect a negative (-) battery lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect the positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

Motor gear rotates counterclockwise
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

Motor gear rotates clockwise
  • If the result is not as specified, replace the power window regulator motor assembly RH.

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ...

    Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL POWER WINDOW REGUL ...

    Other materials:

    Toyota CH-R Service Manual > Smart Key System(for Entry Function): Entry Exterior Alarm does not Sound
    DESCRIPTION The smart key system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (mul ...

    Toyota CH-R Service Manual > Front Seat Outer Belt Assembly: Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY (a) Engage the guide and temporarily install the front sh ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0152