Toyota CH-R Service Manual: Removal

Toyota CH-R Service Manual / Window / Glass / Power Window Regulator Motor(for Rear Door) / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the power window regulator motor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative (-) battery terminal

Initialize back door lock

Power door lock control system

Memorize steering angle neutral point

Lane departure alert system (w/ Steering Control)

Pre-collision system
  • Door window regulator assembly
  • Power window regulator motor assembly
  • Door glass
  • Door glass run

Initialize Power Window Control System
  • Auto up and down function
  • Jam protection function
  • Catch protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Window open warning function

HINT:

  • Use the same procedure for the RH and LH sides.
  • The procedure listed below is for the LH side.

PROCEDURE

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Click here

4. REMOVE REAR DOOR REAR FRAME BRACKET

Click here

5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

6. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Click here

7. REMOVE REAR DOOR BELT SEAL

Click here

8. REMOVE REAR DOOR BELT REAR SEAL

Click here

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

10. REMOVE REAR DOOR FRAME GARNISH

Click here

11. REMOVE REAR DOOR GLASS RUN

Click here

12. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

Click here

13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

14. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

Click here

15. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.
    Components
    COMPONENTS ILLUSTRATION *1 REAR DOOR BELT REAR SEAL *2 REAR DOOR BELT SEAL *3 REAR DOOR GLASS INNER WEATHERSTRIP ...

    Inspection
    INSPECTION CAUTION / NOTICE / HINT NOTICE: Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor. Pe ...

    Other materials:

    Toyota CH-R Service Manual > Lin Communication System: No Response from ID BOX (B2789)
    DESCRIPTION This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more. DTC No. Detection Item DTC Detection Condition Trouble Area ...

    Toyota CH-R Service Manual > Power Window Control System: Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)
    DESCRIPTION If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the power ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0071