Toyota CH-R Service Manual: Brake Hold Operated Indicator Light Circuit

Toyota CH-R Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System / Brake Hold Operated Indicator Light Circuit

DESCRIPTION

The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped due to brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).

The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.

When a malfunction occurs in the brake control system, the brake hold operated indicator light blinks.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click here

PROCEDURE

1.

PRE-CHECK

(a) Check that the brake hold standby indicator light operates normally.

(b) If the brake hold operated indicator light does not illuminate although the brake hold standby indicator light is illuminated, check that the following brake hold operation (maintaining brake oil pressure) conditions are met.

  1. Shift lever is not P or R.
  2. Driver is depressing brake pedal and vehicle is fully stopped.
  3. Driver is not depressing accelerator pedal.
  4. Vehicle is not on steep decline.

HINT:

When a malfunction occurs in the brake control system, the brake hold operated indicator light blinks.

NEXT

2.

INSPECT COMBINATION METER ASSEMBLY

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch off.

(c) Perform the Active Test of the combination meter assembly using the Techstream.

Click here

Body Electrical > Combination Meter > Active Test

Tester Display

Indicat. Hold

(d) Check the combination meter assembly.

OK:

The brake hold operated indicator light turns on or off in accordance with the Techstream operation.

NG

INSPECT METER / GAUGE SYSTEM

OK

3.

PERFORM ACTIVE TEST USING TECHSTREAM (BRAKE HOLD OPERATED INDICATOR LIGHT)

(a) Turn the ignition switch to ON.

(b) Select the Active Test on the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

Indicator light ON/OFF

Observe combination meter

(c) Select the Data List on the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-
Chassis > ABS/VSC/TRAC/EPB > Active Test

Active Test Display

BH Operated Light

Data List Display

BH Operated Light

(d) Check the operating condition of the brake hold operated indicator light when operating it using the Techstream.

Result

Proceed to

Brake hold operated indicator light in the Data List does not change using the Active Test.

A

Brake hold operated indicator light in the Data List turns ON/OFF using the Active Test.

B
A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

USE SIMULATION METHOD TO CHECK

    Brake Warning Light does not Come ON
    DESCRIPTION The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. CAUTION / NOTICE / HINT NOTICE: When replacing the skid c ...

    Brake Hold Standby Indicator Light Circuit
    DESCRIPTION When the brake hold switch (electric parking brake switch assembly) is turned on with the ignition switch turned to ON, the brake hold standby indicator light illuminates when brake h ...

    Other materials:

    Toyota CH-R Service Manual > Continuously Variable Transaxle System: Pressure Control Solenoid "J" Electrical (Shift Solenoid Valve SLP) (P2822)
    DESCRIPTION According to current control by the ECM, the shift solenoid valve SLP controls primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes. *1 Spool Valve *2 Sleeve *3 So ...

    Toyota CH-R Service Manual > Air Conditioning System(for Automatic Air Conditioning System With Side-mounted Air Conditioner Pressure Sensor): System Diagram
    SYSTEM DIAGRAM Communication Table Sender Receiver Signal Communication Line Air conditioning amplifier assembly ECM Magnet Clutch request signal CAN A/C Idleup request signal ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2024 Copyright www.tochr.net
    0.0098