Toyota CH-R Service Manual: Inspection

Toyota CH-R Service Manual / Mirror (ext) / Outer Rear View Mirror Glass / Inspection

INSPECTION

PROCEDURE

1. INSPECT OUTER MIRROR LH

(a) Check the resistance.

(1) Measure the resistance according the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

25°C (77°F)

8.5 to 11.5 Ω

If the result is not as specified, replace the outer mirror LH.

*a

Component without harness connected

(Outer Mirror LH)

(b) Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.

(1) Connect 4 new 1.5 V dry-cell batteries in series.

(2) Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:

Tester Connection

Specified Condition

6 V battery positive (+) → Terminal 1

6 V battery negative (-) → Terminal 2

Outer rear view mirror indicator comes on

If the result is not as specified, replace the outer mirror LH.

*a

Component without harness connected

(Outer Mirror LH)

2. INSPECT OUTER MIRROR RH

(a) Check the resistance.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

25°C (77°F)

8.5 to 11.5 Ω

If the result is not as specified, replace the outer mirror RH.

*a

Component without harness connected

(Outer Mirror RH)

(b) Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.

(1) Connect 4 new 1.5 V dry-cell batteries in series.

(2) Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:

Tester Connection

Specified Condition

6 V battery positive (+) → Terminal 1

6 V battery negative (-) → Terminal 2

Outer rear view mirror indicator comes on

If the result is not as specified, replace the outer mirror RH.

*a

Component without harness connected

(Outer Mirror RH)
    Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE OUTER MIRROR (a) Apply ...

    Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL OUTER MIRROR (a) ...

    Other materials:

    Toyota CH-R Service Manual > Smart Key System(for Entry Function): Entry Exterior Alarm does not Sound
    DESCRIPTION The smart key system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (mul ...

    Toyota CH-R Service Manual > Seat Belt Warning System(w/o Occupant Classification System): On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DRIVER SEAT BELT WARNING SYSTEM HINT: The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. (a) Turn the ignition switch to ON. (b) When the driver seat belt is not fastened, check t ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0134