Toyota CH-R Service Manual: Tire Pressure Warning Light Circuit

Toyota CH-R Service Manual / Tire Pressure Monitoring / Tire Pressure Warning System / Tire Pressure Warning Light Circuit

DESCRIPTION

If the tire pressure warning ECU and receiver detects any problems, the tire pressure warning light blinks (stays on after blinking for 1 minute) and tire pressure monitoring is canceled at the same time. At this time, the ECU stores a DTC in memory.

Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink to output DTCs.

The tire pressure warning ECU and receiver sends the tire pressure warning light illumination request signal to the main body ECU (multiplex network body ECU) via a direct line. The main body ECU (multiplex network body ECU) then sends the signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

    Click here

  • It is necessary to perform initialization after registration of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

PROCEDURE

1.

CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

(a) Check if CAN communication system DTCs are output.

Click here

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B
B

GO TO CAN COMMUNICATION SYSTEM

A

2.

CHECK DTC OUTPUT (B1247)

(a) Clear the DTCs.

Click here

Chassis > Tire Pressure Monitor > Clear DTCs

(b) Turn the ignition switch off.

(c) Turn the ignition switch to ON.

(d) Check for DTCs.

Click here

Chassis > Tire Pressure Monitor > Trouble Codes

OK:

DTC B1247 is not output.

NG

GO TO DTC (B1247)

OK

3.

CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(f) Check the condition of the tire pressure warning light using the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Indicat. Tire Pressure Warning System

Tire pressure warning light

OFF or ON

Perform the test with the vehicle stopped and engine idling.
Body Electrical > Combination Meter > Active Test

Tester Display

Indicat. Tire Pressure Warning System

OK:

The tire pressure warning light turns on or off in accordance with the Techstream operation.

OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

GO TO METER / GAUGE SYSTEM

    ECU Power Source Circuit
    DESCRIPTION This is the power source for the tire pressure warning ECU and receiver. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: When replacing the tire pressure warning ECU and rece ...

    TC and CG Terminal Circuit
    DESCRIPTION DTC output mode is set by connecting terminals 13 (TC) and 4 (CG) of the DLC3. The DTCs are indicated by the blinking of the tire pressure warning light. WIRING DIAGRAM CAUTION / NO ...

    Other materials:

    Toyota CH-R Service Manual > Seat Belt: Rear Seat Inner Belt Assembly(for Rh Side)
    Components COMPONENTS ILLUSTRATION *A w/o Seat Belt Warning System *B w/ Seat Belt Warning System *1 BENCH TYPE REAR SEAT CUSHION ASSEMBLY *2 REAR CENTER SEAT OUTER BELT ASSEMBLY *3 ...

    Toyota CH-R Service Manual > Can Communication System: Check Bus 1 Lines for Short Circuit
    DESCRIPTION There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω. Symptom Trouble Area Resistance b ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0083