Toyota CH-R Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Central Gateway / Data List.
Body Electrical > Central Gateway > Data List|
Tester Display |
|---|
|
IG2 SW |
|
IG1 SW |
|
ACC SW |
|
+B Voltage |
|
Number of DTC |
(e) Read the Data List.
Body Electrical > Central Gateway > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
|---|---|---|---|
|
IG2 SW |
Ignition switch ON signal (IG2 terminal) |
OFF or ON |
OFF: Ignition switch ACC or off ON: Ignition switch ON |
|
IG1 SW |
Ignition switch ON signal (IG1 terminal) |
OFF or ON |
OFF: Ignition switch ACC or off ON: Ignition switch ON |
|
ACC SW |
Ignition switch ACC signal (ACC terminal) |
OFF or ON |
OFF: Ignition switch off ON: Ignition switch ACC or ON |
|
+B Voltage |
Battery voltage (BATT terminal) |
Over 8 V or Under 8 V |
Over 8 V: Battery voltage 8 V or higher Under 8 V: Battery voltage below 8 V |
|
Number of DTC |
Number of DTCs |
0 to 255 |
0: Normal |
Fail-safe Chart
FAIL-SAFE CHART
FAIL-SAFE FUNCTION
(a) When communication fails in any of the CAN bus lines (communication lines),
a fail-safe function(s) will operate. The fail-safe function that is specified fo ...
ECU Malfunction (B1003)
DESCRIPTION
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
Note
B1003
ECU Malfunction
A malf ...
Other materials:
Toyota CH-R Service Manual > Toyota Entune System: System Diagram
SYSTEM DIAGRAM
HINT:
Refer to following systems for details of the system diagram for Toyota Entune
System.
Audio and Visual System (w/o Navigation System)
Click here
Navigation System (w/ Navigation System)
Click here
Safety Connect System
Click he ...
Toyota CH-R Service Manual > Meter / Gauge System: Terminals Of Ecu
TERMINALS OF ECU
COMBINATION METER ASSEMBLY
(a) Disconnect the combination meter assembly connectors.
(b) Measure the voltage on the wire harness side connector according to the value(s)
in the table below.
Terminal No.
Wiring Color
Terminal Description
...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0105