Components
COMPONENTS
ILLUSTRATION
*1 |
REAR AXLE HUB BOLT |
*2 |
REAR DISC |
*3 |
REAR DISC BRAKE CALIPER ASSEMBLY |
*4 |
REAR FLEXIBLE HOSE |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
Replacement
REPLACEMENT
CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. REMOVE REAR WHEEL
Click here
2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
(a) Disconnect the No. 2 parking brake wire assembly connector. |
|
(b) Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.
(c) Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly. NOTICE: Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose. |
|
3. REMOVE REAR DISC
Click here
4. REMOVE REAR AXLE HUB BOLT
(a) Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration. Recommended Service Nut: Thread diameter: 12.0 mm (0.472 in.) Thread pitch: 1.5 mm (0.0591 in.) NOTICE: Install the service nuts to prevent damage to the rear axle hub bolts. |
|
(b) Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
SST: 09611-12010
NOTICE:
Do not damage the threads of the rear axle hub bolts.
5. INSTALL REAR AXLE HUB BOLT
(a) Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly. |
|
(b) Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Recommended Service Nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
HINT:
Recommended washer thickness is 5 mm (0.197 in.) or more.
(c) Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
NOTICE:
(d) Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
6. INSTALL REAR DISC
Click here
7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
(a) Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.
Torque:
107 N·m {1091 kgf·cm, 79 ft·lbf}
(b) Install the rear flexible hose to the rear flexible hose bracket with the bolt.
Torque:
29 N·m {296 kgf·cm, 21 ft·lbf}
(c) Connect the No. 2 parking brake wire assembly connector.
8. INSTALL REAR WHEEL
Click here
Toyota CH-R Service Manual > Rear Brake(for Tmc Made): Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
Click here
2. REMOVE REAR WHEEL
Click here
3. PERFORM REAR BRAKE PAD REPLACEMENT MODE
Click here
4. D ...
Toyota CH-R Service Manual > Compressor(for Valeo Made): Removal
REMOVAL
PROCEDURE
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))
Click here
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))
Click here
3. REMOVE NO. 1 ENGINE UNDER COVER
Click here
4. REMOVE FAN AND GENERATOR V BELT
Click here
...