ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
PROCEDURE
1. CONNECT TECHSTREAM
(a) Connect the Techstream to the DLC3 with the ignition switch off.
(b) Start the engine and run it at idle.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.
HINT:
Refer to the Techstream operator's manual for further details.
2. INSPECT ACTUATOR MOTOR OPERATION
(a) Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test / Motor Relay.
Chassis > ABS/VSC/TRAC/EPB > Active Test
Tester Display |
---|
Motor Relay |
(b) Turn the motor relay on and check for actuator motor operation sounds.
NOTICE:
Do not keep the motor relay on continuously for more than 5 seconds. If it needs to be operated repeatedly, wait an interval of more than 20 seconds between operations.
(c) Turn the motor relay off.
(d) Fully depress the brake pedal and hold it for approximately 15 seconds. Check that the initial brake pedal depth is maintained for the entire 15 seconds.
(e) Turn the motor relay on and check that the brake pedal does not pulsate.
NOTICE:
Do not keep the motor relay on continuously for more than 5 seconds. If it needs to be operated repeatedly, wait an interval of more than 20 seconds between operations.
(f) Turn the motor relay off and release the brake pedal.
3. INSPECT FRONT RIGHT WHEEL OPERATION
(a) Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test / ABS Solenoid.
Chassis > ABS/VSC/TRAC/EPB > Active Test
Tester Display |
---|
ABS Solenoid |
(b) Depress the brake pedal and hold it.
NOTICE:
Do not turn on a solenoid in a manner different than that shown in the following steps.
(c) Turn the SFRH and SFRR solenoids on simultaneously and check that the brake pedal cannot be depressed further.
NOTICE:
Each solenoid operates for 2 seconds and turns off automatically. If a solenoid needs to be operated repeatedly, wait an interval of more than 20 seconds between operations.
(d) Turn the SFRH and SFRR solenoids off simultaneously and check that the brake pedal can be depressed.
(e) With the brake pedal still depressed, enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test / Motor Relay.
Chassis > ABS/VSC/TRAC/EPB > Active Test
Tester Display |
---|
Motor Relay |
(f) Turn the motor relay on and check that the brake pedal returns.
NOTICE:
Do not keep the motor relay on continuously for more than 5 seconds. If it needs to be operated repeatedly, wait an interval of more than 20 seconds between operations.
(g) Turn the motor relay off and release the brake pedal.
4. INSPECT OTHER WHEEL OPERATION
(a) Using the same procedure, check the solenoids for the other wheels.
HINT:
KIA Niro EV / Hybrid (SG2) - (2021-2023) - Owner's manual > Charging electric vehicle: Charging door
Opening the charging door
Operation
Press the right center edge of the
charging door.
The charging door is not open when
the vehicle is locked.
Closing the charging door
Operation
Close the charging door by pressing
rear center edge of the charging door.
Precautions f ...
Toyota CH-R Service Manual > Front Door: Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. INSTALL NO. 2 FRONT DOOR STRIPE
Click here
2. INSTALL FRONT DOOR OUTSIDE STRIPE
Click here
3. INSTALL NO. 4 FRONT D ...