Toyota CH-R Service Manual: Short to +B in Outer Mirror Indicator(Master) (C1AB0)

Toyota CH-R Service Manual / Park Assist / Monitoring / Blind Spot Monitor System / Short to +B in Outer Mirror Indicator(Master) (C1AB0)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (Master) detects a short to +B in the outer rear view mirror indicator LH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AB0

Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
  • The blind spot monitor system is on
  • The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time
  • Outer mirror LH
  • Outer rear view mirror assembly LH
  • Wire harness or connector
  • Blind spot monitor sensor LH (Master)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.

PROCEDURE

1.

CHECK DTC

(a) Turn the ignition switch off.

(b) Turn the ignition switch to ON.

(c) Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

*a

Front view of wire harness connector (to blind spot monitor sensor LH (Master))

(a) Disconnect the blind spot monitor sensor LH (Master) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

M62-4 (OMIL) - Body ground

Ignition switch ON

Below 1 V
OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

3.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

*a

Front view of wire harness connector (to blind spot monitor sensor LH (Master))

(a) Disconnect the IND1 outer mirror LH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

M62-4 (OMIL) - Body ground

Ignition switch to ON

Below 1 V
OK

REPLACE OUTER MIRROR LH

NG

4.

CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

*a

Front view of wire harness connector (to blind spot monitor sensor LH (Master))

(a) Disconnect the J7 outer rear view mirror assembly LH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

M62-4 (OMIL) - Body ground

Ignition switch to ON

Below 1 V
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
    Short to GND in Outer Mirror Indicator(Master) (C1AB2)
    DESCRIPTION This DTC is stored when the blind spot monitor sensor LH (Master) detects a short to ground in the outer rear view mirror indicator LH. DTC No. Detection Item ...

    Steering Angle Sensor (C1A47)
    DESCRIPTION The blind spot monitor sensor receives steering signals from the steering sensor via CAN communication. DTC No. Detection Item DTC Detection Condition ...

    Other materials:

    Toyota CH-R Service Manual > Power Steering System: IG Power Supply Voltage (C1551)
    DESCRIPTION The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit. DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal C ...

    Toyota CH-R Owners Manual > Do-it-yourself maintenance: Do-it-yourself service precautions
    If you perform maintenance by yourself, be sure to follow the correct procedure as given in these sections. Items Parts and tools Battery condition Warm water Baking soda Grease Conventional wrench (for terminal clamp bolts) Brake flui ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0099