Toyota CH-R Service Manual: Illumination Circuit

Toyota CH-R Service Manual / Navigation / Multi Info Display / Navigation System / Illumination Circuit

DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

CHECK ILLUMINATION

(a) Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result

Proceed to

Illumination comes on for all components except steering pad switch assembly.

A

Illumination comes on for all components except radio and display receiver assembly.

B

No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.).

C
B

GO TO STEP 5

C

GO TO LIGHTING SYSTEM

A

2.

CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

(a) Disconnect the F29 spiral cable sub-assembly connector.

*a

Front view of wire harness connector

(to Steering Pad Switch Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

F29-13 (IL+2) - Body ground

Light control switch in tail or head position

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly.

Click here

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

OK

4.

INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Remove the spiral cable sub-assembly.

Click here

(b) Inspect the spiral cable sub-assembly.

Click here

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, COMBINATION METER ASSEMBLY)
NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.

CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

(a) Disconnect the radio and display receiver assembly connector.

*a

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

F131-15 (ILL+) - Body ground

Light control switch in tail or head position

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

6.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the F131 radio and display receiver assembly connector.

(b) Disconnect the F4 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F131-16 (ILL-) - F4-38 (ILL-)

Always

Below 1 Ω

F131-16 (ILL-) or F4-38 (ILL-) - Body ground

Always

10 kΩ or higher
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
    Steering Pad Switch Circuit
    DESCRIPTION This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly. If there is an open in the circuit, the audio system cannot be ...

    Parking Brake Switch Circuit
    DESCRIPTION This circuit is from the skid control ECU (brake actuator assembly) to the radio and display receiver assembly. WIRING DIAGRAM PROCEDURE 1. CHECK ELECTRIC PA ...

    Other materials:

    Toyota CH-R Service Manual > Brake Booster: On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT BRAKE BOOSTER ASSEMBLY (a) Airtightness check (1) Start the engine and stop it after 1 or 2 minutes. Slowly depress the brake pedal several times. If the pedal can be depressed nearly to the floor the first time, but on the 2nd and ...

    Toyota CH-R Service Manual > Navigation System: Voice is not Recognized
    PROCEDURE 1. CHECK CONDITION (a) While paying attention to the condition of the spoken voice command, perform a voice recognition operation. OK: Voice command is recognized normally. HINT: When the voice command is recognized, the content of the voice ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0085