Toyota CH-R Service Manual: Steering Pad Switch Circuit

Toyota CH-R Service Manual / Navigation / Multi Info Display / Navigation System / Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click here

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)

(a) Disconnect the F129 radio and display receiver assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F129-21 (SW1) - F129-24 (SWG)	No switch pushed	95 to 105 kΩ
	Seek+ switch pushed	Below 2.5 Ω
	Seek- switch pushed	313 to 345 Ω
	Volume+ switch pushed	950 to 1050 Ω
	Volume- switch pushed	2955 to 3265 Ω
F129-22 (SW2) - F129-24 (SWG)	No switch pushed	95 to 105 kΩ
	MODE switch pushed	Below 2.5 Ω
	On/off hook switch pushed	950 to 1050 Ω
	Voice switch pushed	2955 to 3265 Ω

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.	INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Inspect the steering pad switch assembly.

Click here

REPLACE STEERING PAD SWITCH ASSEMBLY

3.	INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Remove the spiral cable sub-assembly.

Click here

(b) Inspect the spiral cable sub-assembly.

Click here

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

REPLACE SPIRAL CABLE SUB-ASSEMBLY

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

DESCRIPTION for Automatic Sound Levelizer (ASL): This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly. The Automatic So ...

Illumination Circuit

DESCRIPTION Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position. WIRING DIAGR ...

Other materials:

Toyota CH-R Service Manual > Airbag System: Front Airbag Sensor RH Malfunction (B1610/13)
DESCRIPTION The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH. The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed. DTC B ...

Toyota CH-R Owners Manual > Tire information: Uniform Tire Quality Grading
This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. ...

Toyota CH-R Service Manual: Steering Pad Switch Circuit

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

Illumination Circuit

Other materials:

Toyota C-HR (AX20) 2023-2026 Owner's Manual

Toyota CH-R Owners Manual

Toyota CH-R Service Manual