Toyota CH-R Service Manual: Front Door Pressure Sensor LH (B167A/5A,B167E/5A)

DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the door side airbag sensor LH.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	Test Mode / Check Mode
B167A/5A	Front Door Pressure Sensor LH	Any of the following conditions is met: Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode
B167E/5A	Front Door Pressure Sensor Threshold Malfunction (LH)	Any of the following conditions is met: Door side airbag sensor LH malfunction Airbag sensor assembly malfunction	Door side airbag sensor LH Airbag sensor assembly	Does not apply to test/check mode

DTC Detection Conditions (B167A/5A):

		Vehicle Condition
		Pattern 1	Pattern 2
Diagnosis Condition	Ignition switch ON	○	○
Malfunction Status	Door side airbag sensor LH malfunction	○	-
	Airbag sensor assembly malfunction	-	○
Detection Time		-	-
Number of Trips		1 trip	1 trip

DTC Detection Conditions (B167E/5A):

		Vehicle Condition
		Pattern 1	Pattern 2
Diagnosis Condition	Ignition switch ON	○	○
Malfunction Status	Door side airbag sensor LH malfunction	○	-
	Airbag sensor assembly malfunction	-	○
Detection Time		-	-
Number of Trips		1 trip	1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

PROCEDURE

1.	CHECK DOOR SIDE AIRBAG SENSOR LH

(a) Turn the ignition switch off.

*1 Door Side Airbag Sensor RH *2 No. 2 Side Airbag Sensor LH

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminals to disable the SRS system.

(c) Interchange the door side airbag sensor LH with RH and connect the connectors.

(d) Connect the cable to the negative (-) battery terminal.

(e) Clear the DTCs stored in memory.

Click here

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B166C/4A, B166F/4A, B167A/5A and B167E/5A may be output at this time, but they are not related to this check.

Result	Proceed to
DTC B167A/5A or B167E/5A is output.	A
DTC B166C/4A or B166F/4A is output.	B
DTCs B166C/4A, B166F/4A, B167A/5A and B167E/5A are not output.	C

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Return the door side airbag sensor LH and RH to their original positions and connect the connectors.

A

REPLACE AIRBAG SENSOR ASSEMBLY

B

REPLACE DOOR SIDE AIRBAG SENSOR LH

C

USE SIMULATION METHOD TO CHECK