Toyota CH-R Service Manual: How To Proceed With Troubleshooting

Toyota CH-R Service Manual / Seat / Seat Heater System / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

Use the following procedure to troubleshoot the seat heater system.
*: Use the Techstream.

PROCEDURE

1.	VEHICLE BROUGHT TO WORKSHOP

2.	CUSTOMER PROBLEM ANALYSIS

HINT:

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:

What	Vehicle model, system name
When	Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where	Whether the problem occurs at a specific location
Under what conditions?	Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine has started
How did it happen?	Problem symptoms

3.	INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

4.	CHECK FOR DTC (AIR CONDITIONING SYSTEM)*

(a) Clear the DTCs.

for TMMT Made:
Click here
for TMC Made:
Click here

Body Electrical > Air Conditioner > Clear DTCs

(b) Check for DTCs.

for TMMT Made:
Click here
for TMC Made:
Click here

Body Electrical > Air Conditioner > Trouble Codes

OK:

DTCs are not output

Result	Proceed to
OK	A
NG (for TMMT Made)	B
NG (for TMC Made)	C

GO TO AIR CONDITIONING SYSTEM

5.	CHECK FOR DTC (SEAT HEATER SYSTEM)*

(a) Clear the DTCs.

Click here

Body Electrical > Air Conditioner > Clear DTCs

(b) Recheck for DTCs.

Click here

Body Electrical > Air Conditioner > Trouble Codes

Result	Proceed to
DTCs are not output	A
DTCs are output	B

GO TO DIAGNOSTIC TROUBLE CODE CHART

6.	PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result	Proceed to
Fault is not listed in problem symptoms table	A
Fault is listed in problem symptoms table	B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.	OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Terminals of ECU

Click here

8.	REPAIR OR REPLACE

9.	CONFIRMATION TEST

END

System Description

SYSTEM DESCRIPTION FRONT SEAT HEATER (a) By operating the seat heater switch, the temperature can be controlled within a range of 35 to 42°C (95 to 108°F). (b) The seat heater switch indicator ...

Other materials:

Toyota CH-R Service Manual > Condenser: Installation
INSTALLATION PROCEDURE 1. INSTALL COOLER CONDENSER ASSEMBLY (a) Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration. Install in this Direction (1) Install in this Direction (2) NOTICE: ...

Toyota CH-R Service Manual > Blind Spot Monitor System: Short to GND or Open in Buzzer (C1ABE)
DESCRIPTION DTC C1ABE is stored when the blind spot monitor sensor RH (Slave) detects a short to ground or open in the RCTA buzzer (blind spot monitor buzzer) circuit. DTC No. Detection Item DTC Detection Condition Trouble Area ...

Toyota CH-R Service Manual: How To Proceed With Troubleshooting

System Diagram

System Description

Other materials:

Toyota CH-R Owners Manual

Toyota CH-R Service Manual