Toyota CH-R Service Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body or Smart Key / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ACC SW

Engine switch on (ACC) signal

OFF or ON

OFF: Engine switch off

ON: Engine switch on (ACC)

-

IG SW

Engine switch on (IG) signal

OFF or ON

OFF: Engine switch off or on (ACC)

ON: Engine switch on (IG)

-

RR Door Courtesy SW

Rear door courtesy light switch (for RH) signal

OFF or ON

OFF: Rear door RH closed

ON: Rear door RH open

-

RL Door Courtesy SW

Rear door courtesy light switch (for LH) signal

OFF or ON

OFF: Rear door LH closed

ON: Rear door LH open

-

Back Door Courtesy SW

Back door courtesy light switch signal

OFF or ON

ON: Back door open

OFF: Back door closed

-

FR Door Lock Pos

Front door RH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door RH locked

UNLOCK: Front door RH unlocked

-

FR Door Courtesy SW

Front door courtesy light switch (for RH) signal

OFF or ON

OFF: Front door RH closed

ON: Front door RH open

-

FL Door Lock Pos

Front door LH unlock detection switch signal

LOCK or UNLOCK

LOCK: Front door LH locked

UNLOCK: Front door LH unlocked

-

FL Door Courtesy SW

Front door courtesy light switch (for LH) signal

OFF or ON

OFF: Front door LH closed

ON: Front door LH open

-

RR-Door Lock Pos SW

Rear door RH and LH unlock detection switch signal

OFF or ON

OFF: Rear door RH and LH locked

ON: Rear door RH or LH unlocked

-

RL-Door Lock Pos SW

Rear door RH and LH unlock detection switch signal

OFF or ON

OFF: Rear door RH and LH locked

ON: Rear door RH or LH unlocked

*1

Wireless Control

Wireless door lock control function

OFF or ON

Customize setting displayed

*2

Hazard Answer Back

Hazard light answer-back of wireless function

OFF or ON

Customize setting displayed

-

Wireless Auto Lock

Automatic lock function

OFF or ON

Customize setting displayed

-

Open Door Warning

Open door warning

OFF or ON

Customize setting displayed

-

Unlock 2 Operation

2 press wireless unlock function

OFF or ON

Customize setting displayed

-

Panic Function

Panic function

OFF or ON

Customize setting displayed

*3

Auto Lock Time

Automatic lock time

30 s, 60 s or 120 s

Customize setting displayed

-

Wireless Buzzer Resp

Buzzer answer-back of wireless function

OFF or ON

Customize setting displayed

*3

P/W Wireless Ope Buzz

Power window buzzer answer-back of wireless function

OFF or ON

Customize setting displayed

-

Wireless Buzzer Vol

Wireless door lock buzzer volume

Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

Customize setting displayed

*3

Wireless Lock Function with Doors Open

Side doors reservation lock function

OFF or ON

Customize setting displayed

*3

  • *1: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.
  • *2: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.
  • *3: w/ Toyota Safety Sense P
Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

# Codes

Number of DTCs

0 to 255

Number of stored DTCs

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Door Lock

Door lock motor

OFF/Unlock/Lock

-

D-Door Unlock

Door lock motor

OFF/Unlock/Lock

-

Trunk and Back-Door Open

Back door lock motor

OFF/ON

-

Wireless Buzzer

Wireless door lock buzzer

OFF/ON

-

    Dtc Check / Clear
    DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Smart Key / Tr ...

    Diagnostic Trouble Code Chart
    DIAGNOSTIC TROUBLE CODE CHART Wireless Door Lock Control System DTC No. Detection Item Link B1242 Wireless Door Lock Tuner Circuit Malfun ...

    Other materials:

    Toyota CH-R Service Manual > Front Brake Flexible Hose: Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE FRONT WHEEL Click here 2. DRAIN BRAKE FLUID NOTICE: If brake fluid leaks onto any painted surface, immediately wa ...

    Toyota CH-R Service Manual > Tire Pressure Warning System: Initialization
    INITIALIZATION NOTICE: Initialization can be confirmed through the tire pressure warning light. If the ignition switch off during initialization, the tire pressure warning ECU and receiver memorizes that initialization was being performed. Therefore, it is not necessary to p ...

    © 2017-2019 Copyright www.tochr.net
    0.0205