Toyota CH-R Service Manual: Inspection

Toyota CH-R Service Manual / Lighting (ext) / Rear Combination Light Assembly(for Led Type) / Inspection

INSPECTION

PROCEDURE

1. INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

(a) Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 4 (TRN)

Battery negative (-) → Terminal 3 (E)

Turn signal light comes on

If the result is not as specified, replace the rear combination light assembly LH.

*a

Component without harness connected

(Rear Combination Light Assembly LH)

(b) Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 1 (B)

Battery negative (-) → Terminal 3 (E)

Stop light comes on

If the result is not as specified, replace the rear combination light assembly LH.

(c) Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 2 (TL)

Battery negative (-) → Terminal 3 (E)

Taillight comes on

If the result is not as specified, replace the rear combination light assembly LH.

2. INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

(a) Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 4 (TRN)

Battery negative (-) → Terminal 3 (E)

Turn signal light comes on

If the result is not as specified, replace the rear combination light assembly RH.

*a

Component without harness connected

(Rear Combination Light Assembly RH)

(b) Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 1 (B)

Battery negative (-) → Terminal 3 (E)

Stop light comes on

If the result is not as specified, replace the rear combination light assembly RH.

(c) Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:

Condition

Specified Condition

Battery positive (+) → Terminal 2 (TL)

Battery negative (-) → Terminal 3 (E)

Taillight comes on

If the result is not as specified, replace the rear combination light assembly RH.

    Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE REAR COMBINATION LIGHT ...

    Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL REAR COMBINATION ...

    Other materials:

    Toyota CH-R Service Manual > Navigation Ecu: Removal
    REMOVAL PROCEDURE 1. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY Click here 2. REMOVE FRONT DOOR SCUFF PLATE LH Click here 3. REMOVE COWL SIDE TRIM BOARD LH Click here 4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Click here 5. REMOVE INSTRUMENT PANE ...

    Toyota CH-R Service Manual > Quarter Garnish: Disassembly
    DISASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE QUARTER GARNISH MOULDING (a) Remove the quarter garnish moulding. ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0069