Toyota CH-R Service Manual: License Plate Light Bulb
Components
COMPONENTS
ILLUSTRATION
|
*1 |
LICENSE PLATE LIGHT BULB |
*2 |
NO. 2 BACK DOOR SERVICE HOLE COVER |
|
*3 |
LICENSE PLATE LIGHT SOCKET AND WIRE |
- |
- |
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL LICENSE PLATE LIGHT BULB
(a) Install the license plate light bulb to the license plate light socket and wire as shown in the illustration.
.png) |
Install in this Direction |
(b) Turn the back license plate light socket and wire with the license plate light bulb as shown in the illustration to connect them as a unit.
|
|
Install in this Direction |
2. INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER
(a) Engage the claws to install the No. 2 back door service hole cover as shown in the illustration.
|
|
Install in this Direction |
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
PROCEDURE
1. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER
(a) Using a screw driver with its tip wrapped in protective tape, disengage the claws to remove the No. 2 back door service hole cover as shown in the illustration.
|
*a |
Protective Tape |
.png) |
Remove in this Direction |
2. REMOVE LICENSE PLATE LIGHT BULB
(a) Turn the license plate light socket and wire with the license plate light bulb as shown in the illustration to disconnect them as a unit.
|
|
Remove in this Direction |
(b) Remove the license plate light bulb from the license plate light socket and wire as shown in the illustration.
|
|
Remove in this Direction |
License Plate Light Assembly
Components
COMPONENTS
ILLUSTRATION
*1
LICENSE PLATE LIGHT ASSEMBLY
-
-
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the ...
Lighting System
...
Other materials:
Toyota CH-R Service Manual > Vehicle Stability Control System: Open in ABS Motor Relay Circuit (C146C)
DESCRIPTION
The ABS motor relay supplies power to the pump motor. While the ABS is activated,
the skid control ECU turns the ABS motor relay on to operate the pump motor.
If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage
from the battery or alternator, this DTC ...
Toyota CH-R Service Manual > Vehicle Stability Control System: Brake Actuator Operation Sound is Loud during Initial Check
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform system
variant learning.
Click here
PROCEDURE
1.
PERFORM ROAD TEST
(a) After turning the ignition switch ON, compare the operating sound of the
brake ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
KIA Niro EV / Hybrid (SG2) - (2021-2023) - Owner's manual
0.0097