Toyota CH-R Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Auto High Beam Main Switch |
Auto high beam switch signal |
ON or OFF |
ON: Auto high beam switch pressed OFF: Auto high beam switch not pressed |
- |
|
Dimmer SW |
Dimmer switch high position signal |
ON or OFF |
ON: Dimmer switch in high or high flash position OFF: Dimmer switch in low position |
- |
|
Auto Light SW |
Light control switch AUTO position signal |
ON or OFF |
ON: Light control switch in AUTO position OFF: Light control switch not in AUTO position |
- |
|
Head Light SW (Head) |
Light control switch head position signal |
ON or OFF |
ON: Light control switch in head position OFF: Light control switch not in head position |
- |
|
Light Sensor Illuminance |
Light control sensor illuminance |
0 to 8191 lx |
Value is output according to ambient light levels |
- |
|
Auto H Beam STS0 |
Automatic high beam sensor current state |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
Undetec: Undetected CAM NA: Camera detection malfunction*1 No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: System delay |
|
Auto H Beam STS1 |
Automatic high beam sensor state past 1 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS2 |
Automatic high beam sensor state past 2 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS3 |
Automatic high beam sensor state past 3 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS4 |
Automatic high beam sensor state past 4 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS5 |
Automatic high beam sensor state past 5 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS6 |
Automatic high beam sensor state past 6 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
Auto H Beam STS7 |
Automatic high beam sensor state past 7 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
Condition can be displayed |
*2 |
|
The Number of DTC |
Number of trouble codes |
0 to 255 |
Condition can be displayed |
- |
- *1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.
- *2: Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Dtc Check / Clear
DTC CHECK / CLEAR
CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Tr ...
Fail-safe Chart
FAIL-SAFE CHART
AUTOMATIC HIGH BEAM SYSTEM
(a) The main body ECU (multiplex network body ECU) operates in fail-safe mode
if an abnormal condition such as those listed below has been detected.
...
Other materials:
Toyota CH-R Service Manual > Air Conditioning Unit(for Denso Made): Components
COMPONENTS
ILLUSTRATION
*1
COWL BODY MOUNTING REINFORCEMENT LH
*2
COWL BODY MOUNTING REINFORCEMENT RH
*3
NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
*4
OUTER COWL TOP PANEL SUB-ASSEMBLY
*5 ...
Toyota CH-R Service Manual > Navigation System: Poor Sound Quality in All Modes (Low Volume)
PROCEDURE
1.
CHECK AUDIO SETTINGS
(a) Set treble, middle and bass to the initial values and check that the sound
is normal.
OK:
The sound returns to normal.
HINT:
Sound quality adjustment measures vary according to the type of amplifier.
OK
...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0089