INSTALLATION
CAUTION / NOTICE / HINT
HINT:
When installing the name plates, heat the back door outside garnish and name plates using a heat light.
Heating Temperature|
Item |
Temperature |
|---|---|
|
20 to 30°C (68 to 86°F) |
CAUTION:
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body, back door outside garnish or name plate excessively.
PROCEDURE
1. INSTALL NO. 1 BACK DOOR EMBLEM
(a) Clean the back door outside garnish surface.
(1) Using a heat light, heat the back door outside garnish surface.
(2) Remove any remaining double-sided tape from the back door outside garnish.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Using a heat light, heat the back door outside garnish and a new No. 1 back door emblem.
(c) Remove the release paper from the No. 1 back door emblem.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
|
(d) Engage the 2 pins and install the No. 1 back door emblem as shown in the illustration. |
|
2. INSTALL NO. 1 BACK DOOR NAME PLATE
(a) Clean the back door outside garnish surface.
(1) Using a heat light, heat the back door outside garnish surface.
(2) Remove any remaining double-sided tape from the back door outside garnish.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Using a heat light, heat the back door outside garnish and a new No. 1 back door name plate.
(c) Remove the release paper from the No. 1 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(d) Install the No. 1 back door name plate as shown in the illustration.
|
*a |
Reference Values |
- |
- |
Standard Measurement:
|
Area |
Measurement |
Area |
Measurement |
|---|---|---|---|
|
A |
57.0 mm (2.24 in.) |
B |
85.5 mm (3.37 in.) |
|
C |
83.2 mm (3.28 in.) |
- |
- |
3. INSTALL NO. 2 BACK DOOR NAME PLATE
(a) Clean the back door outside garnish surface.
(1) Using a heat light, heat the back door outside garnish surface.
(2) Remove any remaining double-sided tape from the back door outside garnish.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Using a heat light, heat the back door outside garnish and a new No. 2 back door name plate.
(c) Remove the release paper from the No. 2 back door name plate.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(d) Install the No. 2 back door name plate as shown in the illustration.
|
*a |
Reference Values |
- |
- |
Standard Measurement:
|
Area |
Measurement |
Area |
Measurement |
|---|---|---|---|
|
A |
65.1 mm (2.56 in.) |
B |
113.7 mm (4.48 in.) |
Removal
Quarter GarnishToyota CH-R Service Manual > Wireless Door Lock Control System(w/o Smart Key System): Operation Check
OPERATION CHECK
NOTICE WHEN CHECKING THE FOLLOWING
(a) Wireless door lock/unlock function:
This wireless door lock control function operates only when the following 3 conditions
are met:
(1) There is no key in the ignition key cylinder.
(2) All doors are closed.
(3) The power door lock syste ...
Toyota CH-R Service Manual > Vehicle Stability Control System: Zero Point Calibration of Acceleration Sensor Undone (C1336)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives signals from the yaw
rate and acceleration sensor (airbag sensor assembly) via CAN communication.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and
detects the vehicle's condition using 2 circu ...