Toyota CH-R Service Manual: Problem Symptoms Table

Toyota CH-R Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System / Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

If there are no DTCs output and the problem still occurs, check the suspected areas for each problem symptom in the order given in the following table and proceed to the relevant troubleshooting page.

NOTICE:

When replacing the skid control ECU (brake actuator assembly), sensors, etc., turn the ignition switch off.

HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.

Vehicle Stability Control System

Symptom	Suspected Area	Link
ABS warning light abnormal (Remains on)	Refer to the procedure for "ABS Warning Light Remains ON"
ABS warning light abnormal (Does not come on)	Refer to the procedure for "ABS Warning Light does not Come ON"
Brake warning light / red (malfunction) abnormal (Remains on)	Refer to the procedure for "Brake Warning Light Remains ON"
Brake warning light / red (malfunction) abnormal (Does not come on)	Refer to the procedure for "Brake Warning Light does not Come ON"
Brake hold standby indicator light abnormal	Refer to the procedure for "Brake hold standby indicator light circuit"
Brake hold operated indicator light abnormal	Refer to the procedure for "Brake hold operated indicator light circuit"
Slip indicator light abnormal (Remains on)	Refer to the procedure for "Slip Indicator Light Remains ON"
Slip indicator light abnormal (Does not come on)	Refer to the procedure for "Slip Indicator Light does not Come ON"
TRAC does not operate	Refer to the procedure for "TRAC does not Operate"
Excessive brake pedal travel (No fluid leaks and no air in system)	Refer to the procedure for "Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System)"
ABS does not operate	Refer to the procedure for "ABS does not Operate"
ABS operates before necessary when braking	Refer to the procedure for "ABS Operates Before Necessary When Braking"
VSC does not operate or VSC does not operate correctly	Refer to the procedure for "VSC does not Operate or VSC does not Operate Correctly"
Brake actuator operation sound is loud during initial check	Refer to the procedure for "Brake Actuator Operation Sound is Loud during Initial Check"
VSC OFF switch abnormal	Refer to the procedure for "VSC OFF Switch Circuit"

Test Mode Procedure

TEST MODE PROCEDURE WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK (a) When the ignition switch is turned to ON, check that the ABS warning light, brake system warning light (red indicator), VSC ...

Diagnosis System

DIAGNOSIS SYSTEM DESCRIPTION When troubleshooting a vehicle with a diagnosis system, the only difference from the usual troubleshooting procedure is connecting the Techstream to the vehicle and ...

Other materials:

Toyota CH-R Service Manual > Audio And Visual System(for Radio Receiver Type): No Sound can be Heard from Speakers
PROCEDURE 1. CHECK SETTINGS (a) Check radio receiver assembly setting. (1) Check that the volume is not set to "0". OK: The volume is not set to "0". OK PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE ...

Toyota CH-R Service Manual > Safety Connect System: Acn Call End
ACN CALL END ACN CALL END This function terminates the ACN (Automatic Collision Notification) to the telematics provider. After a collision in which the DCM receives "Collision Detection Signal", the vehicle will send the emergency call notification to the telematics provider until ...

Toyota CH-R Service Manual: Problem Symptoms Table

Test Mode Procedure

Diagnosis System

Other materials:

Toyota C-HR (AX20) 2023-2026 Owner's Manual

Toyota CH-R Owners Manual

Toyota CH-R Service Manual