Toyota CH-R Service Manual: Freeze Frame Data
FREEZE FRAME DATA
CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Body Electrical > Navigation System > Trouble Codes(e) Select a DTC to display its freeze frame data.
LIST OF FREEZE FRAME DATA
Body Electrical > Navigation System|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Battery Voltage |
Battery voltage |
Min.: 0 V, Max.: 24 V |
11 to 14 V |
- |
|
Active Dimmer |
Active dimmer function |
ON or OFF |
ON: Active dimmer function on OFF: Active dimmer function off |
- |
|
Tail Light SW |
Taillight switch |
ON or OFF |
ON: Light control switch in tail or head position OFF: Light control switch off or AUTO |
- |
|
Reverse Signal |
Reverse signal |
ON or OFF |
ON: Shift lever in R OFF: Shift lever not in R |
- |
|
Parking Brake |
Parking brake switch |
ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
|
Ignition |
Engine switch |
ON or OFF |
ON: Engine switch on (IG) OFF: Engine switch off or on (ACC) |
"OFF" is displayed even though the engine switch is on (ACC) |
|
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
HDMI Line(Blu-ray Disc Player) |
- |
Disconnected or Connected |
Disconnected |
Not available |
Dtc Check / Clear
DTC CHECK / CLEAR
CHECK DTC (CHECK USING TECHSTREAM)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG) and wait for 90 seconds.
(c) Turn the Techstream on.
(d) Enter the ...
Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when decidi ...
Other materials:
Toyota CH-R Service Manual > Navigation System: Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter
DESCRIPTION
The navigation ECU receives a vehicle speed signal from the combination meter
assembly.
HINT:
A voltage of 12 V or 5 V is output from each ECU and then input to the
combination meter assembly. The signal is changed to a pulse signal at the
transistor in the combinati ...
Toyota CH-R Service Manual > Automatic Headlight Beam Level Control System: Initialization has not been Performed (B2450)
DESCRIPTION
The headlight ECU sub-assembly LH stores this DTC if initialization has not been
performed after the ECU was replaced.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
Note
B2450
Initializat ...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0123