Toyota CH-R Service Manual: Cellular Phone Inspection

PROCEDURE

1.

CHECK USAGE CONDITION

(a) Check that the vehicle and cellular phone meet the following conditions:

NOTICE:

If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.

  • The cellular phone is "Bluetooth" compatible.

    Click here

  • The cellular phone is registered as a hands-free device.
  • "Bluetooth" setting of the cellular phone is on.
  • Operating system and software of the cellular phone are the latest versions.
  • There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.
  • The "Wi-Fi" setting of the cellular phone is off.
  • The "Wi-Fi" tethering setting of the cellular phone is off.

(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result

Proceed to

The cellular phone is connected correctly.

A

The cellular phone is not connected correctly.

B

A

END

B

2.

RESTART CELLULAR PHONE

(a) Restart the cellular phone.

(b) Turn the engine switch off.

(c) Turn the engine switch on (ACC).

(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result

Proceed to

The cellular phone is connected correctly.

A

The cellular phone is not connected correctly.

B

A

END

B

3.

CHECK OPERATION

(a) Check if the in-vehicle device can be recognized by the cellular phone.

Result

Proceed to

In-vehicle device can be recognized.

A

In-vehicle device cannot be recognized.

B

B

GO TO STEP 5

A

4.

REGISTER AGAIN

(a) Clear all "Bluetooth" devices registered to the cellular phone and the radio and display receiver assembly.

(b) Register the cellular phone again.

(c) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result

Proceed to

The cellular phone is connected correctly.

A

The cellular phone is not connected correctly.

B

A

END

B

5.

CHECK USING ANOTHER VEHICLE

(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.

HINT:

  • Make sure to obtain the customer's permission to perform this procedure.
  • After the inspection, clear the registered information and usage history acquired during the inspection.

Result

Proceed to

The cellular phone is connected correctly.

A

The cellular phone is not connected correctly.

B

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

6.

CHECK USING ANOTHER CELLULAR PHONE

(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.

HINT:

  • Make sure to obtain the customer's permission to perform this procedure.
  • After the inspection, clear the registered information and usage history acquired during the inspection.

Result

Proceed to

The cellular phone is connected correctly.

A

The cellular phone is not connected correctly.

B

A

END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Cellular Phone Registration Failure
    CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be neede ...

    Sound of Portable Player cannot be Heard from Speakers or Sound is Low
    PROCEDURE 1. CHECK PORTABLE PLAYER SETTINGS (a) Check the portable player settings. (1) Check that the volume is not set to "0". (2) Check that mute is of ...

    Other materials:

    Toyota CH-R Service Manual > Vehicle Stability Control System: Yaw Rate Sensor (C1234,C1472,C1474)
    DESCRIPTION The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication. HINT: If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the ...

    Toyota CH-R Service Manual > Wireless Door Lock Control System(w/o Smart Key System): Only Wireless Control Function is Inoperative
    DESCRIPTION The door control and tire pressure monitoring system receiver assembly receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by s ...

    © 2017-2021 Copyright www.tochr.net
    0.0171