Toyota CH-R Service Manual: Green Indicator Remains Off

Toyota CH-R Service Manual / Cellular Communication / Safety Connect System / Green Indicator Remains Off

DESCRIPTION

After turning the ignition switch ON, the DCM (Telematics Transceiver) will enter into self check mode. The manual (SOS) switch red indicator will illuminate for 2 seconds and turn off followed by the manual (SOS) switch green indicator illuminating and remaining on under normal operation. If neither the red nor green indicators remain on, verification of the subscription should be performed.

PROCEDURE

1.

CONFIRM GREEN INDICATOR COMES ON

(a) After the ignition switch turned to ON and the manual (SOS) switch red indicator has come on for 2 seconds, confirm that the manual (SOS) switch green indicator comes on for 2 seconds.

OK:

Green indicator comes on.

NG

GO TO STEP 6

OK

2.

CONFIRM SUBSCRIPTION MODE

(a) Confirm the indicator status 5 seconds after the ignition switch turned to ON.

Result

Proceed to

Green indicator remains on

A

Green indicator remains off

B

Red and Green indicators both flash(1 second intervals, for 20 seconds)

C

HINT:

If red and green indicators are flashing, the system is in shipping mode, so the system should be changed to either active mode or deactive mode.

A

CHECK FOR INTERMITTENT PROBLEMS

C

CHANGE SUBSCRIPTION MODE
B

3.

INPUT VIN WITH TECHSTREAM

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch ON and wait for 10 seconds.

(d) Turn the Techstream on.

(e) Select "Vehicle Inquiry" and input the VIN.

NEXT

4.

CONFIRM SUBSCRIPTION MODE

(a) Confirm the indicator status at 5 seconds after the ignition switch turned to ON.

Result

Proceed to

Green indicator remains on

A

Green indicator remains off

B
A

END
B

5.

REPLACE DCM (TELEMATICS TRANSCEIVER)

(a) Replace the DCM (Telematics Transceiver).

Click here

NOTICE:

  • The ignition switch must be off.
  • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.
NEXT

PERFORM DCM ACTIVATION

6.

CHECK DTC

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch ON and wait for 10 seconds.

(d) Turn the Techstream on.

(e) Perform "Health Check" and check for current DTCs.

Click here

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

7.

REPLACE DCM (TELEMATICS TRANSCEIVER)

(a) Replace the DCM (Telematics Transceiver).

Click here

NOTICE:

  • The ignition switch must be off.
  • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.
NEXT

PERFORM DCM ACTIVATION

    Green And Red Indicators Do Not Come On When Ig-on
    DESCRIPTION If the red and green indicators fail to illuminate after the ignition switch turned to ON, the vehicle does not recognize the DCM (Telematics Transceiver). The DCM (Telematics Transce ...

    Red Indicator Remains On
    DESCRIPTION This means that the DCM (Telematics Transceiver) has detected a malfunction in the safety connect system and stored a DTC. PROCEDURE 1. CHECK DTC (a) ...

    Other materials:

    Toyota CH-R Service Manual > Smart Key System(for Start Function): Parts Location
    PARTS LOCATION ILLUSTRATION *1 PARK/NEUTRAL POSITION SWITCH *2 STARTER ASSEMBLY *3 NO. 1 ENGINE ROOM RELAY BLOCK - IG2-MAIN FUSE - ECU-IG2 NO. 1 FUSE - ST FUSE - WIPER FUSE - ST RELAY *4 ...

    Toyota CH-R Service Manual > Airbag System: Short in Driver Side Squib Circuit (B1800/51-B1803/51)
    DESCRIPTION The driver side squib circuit consists of the airbag sensor assembly, spiral cable with sensor sub-assembly and horn button assembly. The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. These DTCs are stored when a malfunction is d ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0151