Toyota CH-R Service Manual: Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)

Toyota CH-R Service Manual / Audio / Video / Audio And Visual System(for Radio And Display Type) / Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)

DESCRIPTION

This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the audio and visual system vehicle customization screen.

HINT:

The certification ECU (smart key ECU assembly) controls the smart key system related items that are customizable via the audio and visual system vehicle customization screen.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15F7

Certification ECU Vehicle Information Reading/Writing Process Malfunction

Certification ECU (smart key ECU assembly) vehicle setting processing malfunction
  • CAN communication system
  • Smart key system
  • Certification ECU (smart key ECU assembly)
  • Radio and display receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for audio and visual system (for Radio and Display Type).

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC is stored.
    • The radio and display receiver assembly may not operate normally.
  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    w/ Smart Key System: Click here

    w/o Smart Key System: Click here

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

OK:

CAN communication DTCs are not output.

NG

GO TO CAN COMMUNICATION SYSTEM

OK

2.

CHECK SMART KEY SYSTEM

(a) Check if the smart entry and start system is malfunctioning.

  • for Entry Function: Click here
  • for Start Function: Click here

HINT:

Customization may not be possible depending on the malfunction in the smart entry and start system.

OK:

No malfunctions are present in the smart key system.

 

Proceed to

OK

A

NG (for Entry Function)

B

NG (for Start Function)

C
B

GO TO SMART KEY SYSTEM

C

GO TO SMART KEY SYSTEM

A

3.

CHECK CUSTOMIZE ITEMS

(a) Make a note of the customizable items for the certification ECU related system.

HINT:

The items shown as customizable via the audio and visual system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.

(1) To match-up the items on the audio and visual system vehicle customization screen with the items on the Techstream, check the customize parameters list for the smart key system related items that can be customized via the audio and visual system vehicle customization screen.

for Entry Function: Click here

for Start Function: Click here

(b) Using the Techstream, confirm that it is possible to change the settings of the customize parameters that are available for customization via the audio and visual system vehicle customization screen.

OK:

The items available for customization via the audio and visual system vehicle customization screen can be customized successfully using the Techstream.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    Sending Malfunction (Navigation to APGS) (U0073,U0100,U0129,U0140,U0155,U0164)
    DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. Detection Item DTC Detection Condition Trouble Area ...

    XM Tuner Antenna Disconnected (B15FE,B15FF)
    DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the radio and display receiver assembly. DTC No. Detection Item ...

    Other materials:

    Toyota CH-R Service Manual > Blind Spot Monitor System: Blind Spot Monitor Slave Module (C1AB7)
    DESCRIPTION This DTC is stored when the blind spot monitor sensor RH (Slave) detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB7 Blind Spot Monitor Slave Module The b ...

    Toyota CH-R Service Manual > Headlight Assembly(for Halogen Headlight): Reassembly
    REASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL FRONT SIDE MARKER LIGHT BULB (for USA and Canada) (a) Install the front side marker light bulb to the front side marke ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0067