Toyota CH-R Service Manual: How To Proceed With Troubleshooting

Toyota CH-R Service Manual / Audio / Video / Audio And Visual System(for Radio And Display Type) / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the audio and visual system.
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP
NEXT

2.

CUSTOMER PROBLEM ANALYSIS
  • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

    What

    Vehicle model, system name

    When

    Date, time, occurrence frequency

    Where

    Road conditions

    Under what conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem symptoms
NEXT

3.

INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

NEXT

4.

CHECK CABIN

(a) Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

OK:

Condensation is not likely being produced and the temperature is not high or extremely low.

HINT:

  • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
  • The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
NG

SET CABIN TO APPROPRIATE TEMPERATURE
OK

5.

CHECK CAN COMMUNICATION SYSTEM*

(a) Check for DTCs.

Click here

Result

Proceed to

CAN DTCs are not output.

A

CAN DTCs are output.

B
B

GO TO CAN COMMUNICATION SYSTEM

A

6.

CHECK FOR DTC*

(a) Refer to DTC Check/Clear.

Click here

Result

Proceed to

DTCs are output.

A

DTCs are not output.

B
B

GO TO STEP 10

A

7.

DTC CLEAR*

(a) Refer to DTC Check/Clear.

Click here

HINT:

The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.

NEXT

8.

RECHECK FOR DTC*

(a) Refer to DTC Check/Clear.

Click here

Result

Proceed to

DTCs are output.

A

DTCs are not output.

B

HINT:

  • Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
  • If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the Techstream.
  • Check the DTCs and inspect the area that the code indicates.
B

GO TO STEP 10

A

9.

DIAGNOSTIC TROUBLE CODE CHART

(a) Find the output code in Diagnostic Trouble Code Chart.

Click here

NEXT

GO TO STEP 12

10.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table.

A

Fault is listed in Problem Symptoms Table.

B

HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click here

B

GO TO STEP 12

A

11.

PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

(a) Refer to Terminals of ECU.

Click here

NEXT

12.

CHECK CIRCUIT

(a) Adjust, repair or replace as necessary.

NEXT

13.

RECHECK FOR DTC*

(a) After clearing DTCs, recheck for DTCs.

Click here

Body Electrical > Navigation System > Clear DTCs Body Electrical > Navigation System > Trouble Codes
NEXT

14.

PERFORM CONFIRMATION TEST
NEXT

END
    System Description
    SYSTEM DESCRIPTION USB AUDIO SYSTEM FUNCTION OUTLINE (a) The No. 1 stereo jack adapter assembly is equipped with a USB connector. Connecting a USB device or "iPod" to the No. 1 stereo ja ...

    Operation Check
    OPERATION CHECK STORAGE CHECK (DCU STORAGE CHECK) NOTICE: When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which ...

    Other materials:

    Toyota CH-R Service Manual > Audio And Visual System(for Radio And Display Type): USB Audio System Recognition/Play Error
    DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnostic procedure is for when a de ...

    Toyota CH-R Service Manual > Navigation System: Illumination for Panel Switch does not Come on with Tail Switch ON
    CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System. Click here When replacing the radio ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0085