DESCRIPTION
The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.
WIRING DIAGRAM
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
(a) Disconnect the F47 radio receiver assembly connector.
(b) Disconnect the R2 map light assembly (telephone microphone assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
F47-6 (SNS2) - R2-1 (SNS2) |
Always |
Below 1 Ω |
|
F47-4 (MACC) - R2-9 (MACC) |
Always |
Below 1 Ω |
|
F47-5 (MIN+) - R2-8 (MCO+) |
Always |
Below 1 Ω |
|
F47-19 (MIN-) - R2-7 (MCO-) |
Always |
Below 1 Ω |
|
F47-6 (SNS2) or R2-1 (SNS2) - Body ground |
Always |
10 kΩ or higher |
|
F47-4 (MACC) or R2-9 (MACC) - Body ground |
Always |
10 kΩ or higher |
|
F47-5 (MIN+) or R2-8 (MCO+) - Body ground |
Always |
10 kΩ or higher |
|
F47-19 (MIN-) or R2-7 (MCO-) - Body ground |
Always |
10 kΩ or higher |
|
F47-18 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG | |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
INSPECT RADIO RECEIVER ASSEMBLY |
(a) Connect the F47 radio receiver assembly connector.
(b) Connect the R2 map light assembly (telephone microphone assembly) connector.
|
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
F47-18 (SGND) - Body ground |
Always |
Below 1 Ω |
|
F47-19 (MIN-) - Body ground |
Always |
Below 1 Ω |
| NG | |
REPLACE RADIO RECEIVER ASSEMBLY |
|
|
3. |
INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
(a) Remove the map light assembly (telephone microphone assembly).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | |
REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
|
|
4. |
INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
(a) Connect the R2 map light assembly (telephone microphone assembly) connector.
(b) Turn the ignition switch to ACC.
|
(c) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector. |
|
(d) Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
|
Result |
Proceed to |
|---|---|
|
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. |
A |
|
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. |
B |
| A | |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B | |
REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Speaker Circuit
Radio Receiver Power Source CircuitToyota CH-R Service Manual > Navigation System: Mute Signal Circuit between Radio Receiver and Telematics Transceiver
DESCRIPTION
The telematics transceiver sends a mute signal to the radio and display receiver
assembly.
The radio and display receiver assembly controls the volume according to the
mute signal from the telematics transceiver.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the ...
Toyota CH-R Service Manual > Pre-collision System: Parts Location
PARTS LOCATION
ILLUSTRATION
*1
FRONT SPEED SENSOR RH
*2
FRONT SPEED SENSOR LH
*3
REAR SKID CONTROL SENSOR RH
*4
REAR SKID CONTROL SENSOR LH
ILLUSTRATION
*1
BRAKE ACTUA ...