Toyota CH-R Service Manual: Operation Check

OPERATION CHECK

NOTICE:

Make sure that the smart key system (for Start Function) has not been canceled before performing this inspection.

Click here

OPERATION DESCRIPTION

(a) Push-button start function:

(1) When the electrical key transmitter sub-assembly is in a vehicle interior detection area and the brake pedal is depressed, the engine is started by pressing the engine switch.

(2) When the electrical key transmitter sub-assembly is in a vehicle interior detection area and the brake pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.

(3) After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed while not depressing the brake pedal, the power source mode will change to on (ACC) and "ACCESSORY" will be displayed on the multi-information display.

*a

"ACCESSORY" Display

(4) After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed 2 times without depressing the brake pedal, the power source mode will change to on (IG) and "IGNITION ON" will be displayed on the multi-information display.

*a

"IGNITION ON" Display

(5) After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the brake pedal is depressed while the shift lever is in P, the key indicator display will be displayed on the multi-information display.

*a

Key Indicator Display

(6) The engine will start if the engine switch is pressed when the key indicator display is displayed.

(b) Changing the power source mode when the electrical key transmitter sub-assembly is not operating correctly due to wave interference or transmitter battery depletion:

(1) Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

(2) While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

(3) A buzzer in the combination meter assembly will sound and the power source mode will change to on (IG) and "IGNITION ON" will be displayed on the multi-information display.

*a

"IGNITION ON" Display

(4) Pressing the engine switch without depressing the brake pedal changes the power source mode from on (IG) to off.

(c) Starting the engine when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:

(1) Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

(2) While depressing the brake pedal with the shift lever in P and facing the logo side of the electrical key transmitter sub-assembly toward the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

(3) A buzzer in the combination meter assembly will sound, the power source mode will change to on (IG) and the key indicator display will be displayed on the multi-information display.

*a

Key Indicator Display

(4) Press the engine switch with the brake pedal depressed to start the engine.

CHECK PUSH-BUTTON START FUNCTION

(a) Check the push-button start function:

(1) Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off. With the shift lever in P, check that the key indicator display is displayed when the brake pedal is depressed. Check that the engine starts when the engine switch is pressed after the key indicator display is displayed on the multi-information display.

*a

Key Indicator Display

(2) While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the engine switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.

HINT:

If the engine switch is pressed with the engine switch on (IG) and the shift lever not in P, the power source mode will not change to off, but to on (ACC).

(3) With the shift lever in P, check that the steering lock operates when a door is opened.

HINT:

When the engine switch is pressed after the vehicle is stopped, the engine will stop and all power will turn off. However, if the shift lever is not in P when the engine switch is pressed with the vehicle stopped, the power source mode will not change to off, but to on (ACC).

(4) Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

    Click here

  • Perform this inspection for both inspection points.

*a

Inspection Point

(5) Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (front floor) or No. 3 indoor electrical key antenna assembly (inside luggage compartment).

    Click here

  • Perform this inspection for both inspection points.

*a

Inspection Point

(6) Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

    Click here

  • Perform this inspection for both inspection points.

*a

Inspection Point

CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION

(a) Check the transmitter battery saving mode function:

(1) Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.

(2) Check that the smart key system (for Start Function) does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.

CHECK POWER SOURCE MODE CHANGING FUNCTION

(a) Check the engine switch.

(1) Check that the power source mode changes according to the chart below.

Shift Position

Brake Pedal

Power Source Mode when Engine Switch Pressed

P

Released

Off → on (ACC) → on (IG) → off

P

Released

Engine running → off

P

Released

On (ACC)* → off

P

Depressed

Off → engine starts

P

Depressed

On (ACC) → engine starts

P

Depressed

On (IG) → engine starts

P

Depressed

Engine running → off

P

Depressed

On (ACC)* → off

N

Released

Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)

N

Released

Engine running → on (ACC)

N

Depressed

Off → engine starts

N

Depressed

On (ACC) → engine starts

N

Depressed

On (IG) → engine starts

N

Depressed

Engine running → on (ACC)

Not P or N

Released

Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)

Not P or N

Released

Engine running → on (ACC)

Not P or N

Depressed

Off → on (IG)

Not P or N

Depressed

On (ACC) → on (IG)

Not P or N

Depressed

Engine running → on (ACC)

HINT:

*: This situation is only applicable when the power source mode has changed from on (IG) to on (ACC). (Excluding an emergency stop by pressing the engine switch 3 times quickly or pressing and holding the engine switch for 2 seconds or more.)

CHECK POWER SOURCE MODE INDICATION

(a) Check the key indicator display.

*a

"ACCESSORY" Display

*b

"IGNITION ON" Display

*c

Key Indicator Display

-

-

Multi-information Display Inspection

Power Source Mode

Multi-information Display

Off

(Excluding conditions in which the engine can be started)

Off

On (ACC)

(Excluding conditions in which the engine can be started)

"ACCESSORY" displayed

On (IG)

(Excluding conditions in which the engine can be started)

"IGNITION ON" displayed

Condition in which engine can be started*1

Key Indicator displayed

Engine started

Off

HINT:

*1: Indicates the conditions in which the engine can be started by pressing the engine switch while either of the following conditions is met:

  • Condition 1

    All of the following conditions are met:

    • The power source mode was changed from on (IG) to on (ACC).
    • Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).
    • The shift lever is in N and the steering is unlocked.
    • The stop light switch assembly is on.
  • Condition 2

    All of the following conditions are met:

    • The power source mode was not changed from on (IG) to on (ACC).
    • Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).
    • The stop light switch assembly is on.
    • The shift lever is in P, or the shift lever is in N with the steering unlocked.

*2: When the electrical key transmitter sub-assembly is in the cabin, the ID code sent as a result of communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the cabin.

    Customize Parameters
    CUSTOMIZE PARAMETERS CUSTOMIZE SMART KEY SYSTEM (for Start Function) NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. ...

    Problem Symptoms Table
    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are lis ...

    Other materials:

    Toyota CH-R Service Manual > Can Communication System: Blind Spot Monitor Sensor Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Blind Spot Monitor Sensor Communication Stop Mode Any of the following conditions are met: Communication stop for "Blind Spot Monitor Master" is indicated on th ...

    Toyota CH-R Service Manual > Audio And Visual System(for Radio Receiver Type): Terminals Of Ecu
    TERMINALS OF ECU Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition F47-4 (MACC) - F48-7 (GND1) B - LA Microphone power supply Ignition switch off ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    KIA Niro EV / Hybrid (SG2) - (2021-2023) - Owner's manual

    © 2017-2024 Copyright www.tochr.net
    0.019