Toyota CH-R Service Manual: Trouble in Passenger Airbag ON/OFF Indicator
DESCRIPTION
The occupant classification system detects the front passenger seat condition. It then displays the instrument panel passenger airbag assembly and front seat cushion airbag assembly RH condition (activated/not activated) using the passenger airbag ON/OFF indicator.
HINT:
Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.
|
Front Passenger Seat Condition |
Passenger Airbag ON/OFF Indicator |
SRS Warning Light |
|
|---|---|---|---|
|
ON Indicator |
OFF Indicator |
||
|
Vacant |
OFF |
ON |
OFF |
|
Adult*1 is seated |
ON |
OFF |
OFF |
|
Child*2 is seated |
ON or OFF*2 |
OFF or ON*2 |
OFF |
|
Child restraint system is installed |
OFF |
ON |
OFF |
|
Occupant classification system failure |
OFF |
ON |
ON |
- *1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.
- *2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.
CAUTION / NOTICE / HINT
NOTICE:
- After turning the ignition switch off, waiting time may be required
before disconnecting the cable from the negative (-) battery terminal. Therefore,
make sure to read the disconnecting the cable from the negative (-) battery
terminal notices before proceeding with work.
Click here
.gif)
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. |
CHECK SRS WARNING LIGHT |
(a) Turn the ignition switch to ON, and check the SRS warning light condition.
OK:
After the primary check period, the SRS warning light goes off.
HINT:
The primary check is performed for approximately 6 seconds after the ignition switch is turned ON.
| NG | .gif) |
GO TO AIRBAG SYSTEM |
|
.gif)
|
2. |
PERFORM ZERO POINT CALIBRATION |
(a) Using the Techstream, perform Zero Point Calibration.
Click here
|
Tester Display |
|---|
|
Zero Point Calibration |
OK:
"Zero Point Calibration is complete." is displayed.
| OK | |
END |
|
|
3. |
RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT |
(a) Loosen the 4 installation bolts of the front seat assembly RH.
(b) Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
Click here
|
|
4. |
PERFORM ZERO POINT CALIBRATION |
(a) Using the Techstream, perform Zero Point Calibration.
Click here
|
Tester Display |
|---|
|
Zero Point Calibration |
OK:
"Zero Point Calibration is complete." is displayed.
| OK | |
END |
|
|
5. |
READ VALUE USING TECHSTREAM |
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / Occupant Detection / Data List.
(f) Read the Data List according to the display on the Techstream.
Body Electrical > Occupant Detection > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Passenger Buckle SW |
Passenger side buckle switch |
NG, Set or Unset |
Set: Front passenger seat belt is fastened Unset: Front passenger seat belt is not fastened |
"NG" will be displayed immediately after the ignition switch is turned on. |
|
Tester Display |
|---|
|
Passenger Buckle SW |
OK:
The Techstream display changes correctly in accordance with the operation of the passenger side buckle switch.
| NG | |
GO TO STEP 9 |
|
|
6. |
CHECK CONNECTORS |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Disconnect the connectors from the occupant detection ECU, front in weight detection sensor sub-assembly and rear in weight detection sensor sub-assembly.
(d) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG | |
REPLACE FRONT SEAT WIRE RH |
|
|
7. |
REPLACE OCCUPANT DETECTION ECU |
(a) Connect the connectors to the front in weight detection sensor sub-assembly and rear in weight detection sensor sub-assembly.
(b) Replace the occupant detection ECU.
Click here
(c) Connect the cable to the negative (-) battery terminal.
|
|
8. |
PERFORM ZERO POINT CALIBRATION |
(a) Using the Techstream, perform Zero Point Calibration.
Click here
|
Tester Display |
|---|
|
Zero Point Calibration |
| NEXT | |
END |
|
9. |
CHECK CONNECTORS |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
(d) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG | |
REPLACE FRONT SEAT WIRE RH |
|
|
10. |
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Replace the front seat inner belt assembly RH.
Click here
(d) Connect the cable to the negative (-) battery terminal.
|
|
11. |
PERFORM ZERO POINT CALIBRATION |
(a) Using the Techstream, perform Zero Point Calibration.
Click here
|
Tester Display |
|---|
|
Zero Point Calibration |
| NEXT | |
END |
Passenger Side Buckle Switch Circuit Malfunction (B1771)
DESCRIPTION
The passenger side buckle switch circuit consists of the occupant detection ECU
and passenger side buckle switch (front seat inner belt assembly RH).
DTC B1771 is stored when a malfunc ...
Other materials:
Toyota CH-R Service Manual > Front Bumper: Removal
REMOVAL
PROCEDURE
1. REMOVE RADIATOR COVER
(a) Remove the 2 hood bumper cushions.
(b) Remove the 4 clips.
(c) Disengage the guides to remove the radiator cover as shown in the illustration.
Remove in this Directio ...
Toyota CH-R Service Manual > Smart Key System(for Entry Function): Back Door Entry Unlock Function does not Operate
DESCRIPTION
If the entry unlock function does not operate for the back door only, but the
entry lock function operates, the request code is being transmitted properly from
the back door. In this case, there may be a problem related to the open switch (connection
between the back door opener s ...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0139