Toyota CH-R Service Manual: On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
CAUTION:
Be sure to correctly follow the removal and installation procedures for the curtain shield airbag assemblies.
PROCEDURE
1. INSPECT CURTAIN SHIELD AIRBAG ASSEMBLY (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check.
Click here .gif)
(b) Visually check for defects with the curtain shield airbag assemblies installed to the vehicle.
HINT:
The defects are as follows:
- Cuts on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies
- Small cracks on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies
- Significant discoloration on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies
OK:
No defects are found.
If any defects are found, replace each pillar garnish or the roof headlining assembly with a new one.
2. INSPECT CURTAIN SHIELD AIRBAG ASSEMBLY (for Vehicle Involved in Collision and Airbag not Deployed)
(a) Perform a diagnostic system check.
Click here
(b) Visually check for defects with the curtain shield airbag assemblies removed from the vehicle.
HINT:
The defects are as follows:
- Cuts
- Small cracks
- Significant discoloration
- Cracks or other damage to the connector
OK:
No defects are found.
If any defects are found, replace the curtain shield airbag assembly with a new one.
Components
COMPONENTS
ILLUSTRATION
*1
CURTAIN SHIELD AIRBAG ASSEMBLY
*2
CLIP
*3
CURTAIN SHIELD AIRBAG CLIP SPACER
-
...
Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed, installed, or replaced during th ...
Other materials:
Toyota CH-R Service Manual > Wheel Opening Moulding(for Rear): Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL NO. 1 BODY OUTSIDE MOULDING PAD
HINT:
When installing the No. 1 body outside moulding pad, heat the quarter outside
...
Toyota CH-R Service Manual > Steering Pad: Installation
INSTALLATION
PROCEDURE
1. INSTALL HORN BUTTON ASSEMBLY
(a) Check that the ignition switch off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-)
battery terminal to disable th ...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0064