DESCRIPTION
The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
DTC B1610/13 is stored when a malfunction is detected in the front airbag sensor RH.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Test Mode / Check Mode |
---|---|---|---|---|
B1610/13 |
Front Airbag Sensor RH Malfunction |
Any of the following conditions is met:
|
|
Does not apply to test/check mode |
Vehicle Condition |
|||
---|---|---|---|
Pattern 1 |
Pattern 2 |
||
Diagnosis Condition |
Ignition switch ON |
○ |
○ |
Malfunction Status |
Front airbag sensor RH malfunction |
○ |
- |
Airbag sensor assembly malfunction |
- |
○ |
|
Detection Time |
- |
- |
|
Number of Trips |
1 trip |
1 trip |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
1. |
CHECK FLOOR SIDE AIRBAG SENSOR RH |
(a) Turn the ignition switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the front airbag sensor RH with LH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Clear the DTCs stored in memory.
Click here
(f) Turn the ignition switch off.
(g) Turn the ignition switch ON, and wait for at least 60 seconds.
(h) Check for DTCs.
Click here
HINT:
Codes other than DTCs B1610/13 and B1615/14 may be output at this time, but they are not related to this check.
Result |
Proceed to |
---|---|
DTCs B1610/13 and B1615/14 are not output. |
A |
DTC B1610/13 is output. |
B |
DTC B1615/14 is output. |
C |
(i) Turn the ignition switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Return the front airbag sensor RH and LH to their original positions and connect the connectors.
A | ![]() |
USE SIMULATION METHOD TO CHECK |
B | ![]() |
REPLACE AIRBAG SENSOR ASSEMBLY |
C | ![]() |
REPLACE FRONT AIRBAG SENSOR RH |
Toyota CH-R Service Manual > Steering Lock System: Parts Location
PARTS LOCATION
ILLUSTRATION
*1
FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
-
-
ILLUSTRATION
*1
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
*2
STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BR ...
Toyota CH-R Service Manual > Ptc Heater Assembly: Removal
REMOVAL
PROCEDURE
1. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
2. REMOVE COWL SIDE TRIM BOARD LH
Click here
3. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
4. REMOVE NO. 1 AIR DUCT
Click here
5. REMOVE NO. 2 HEATER COVER (for VALEO Made)
( ...