DESCRIPTION
The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and floor side airbag sensor RH.
The floor side airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
DTC B162A/2A is stored when a malfunction is detected in the floor side airbag sensor RH.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Test Mode / Check Mode |
|---|---|---|---|---|
|
B162A/2A |
Side Airbag Sensor Assembly No.2 (RH) |
Any of the following conditions is met:
|
|
Does not apply to test/check mode |
|
Vehicle Condition |
|||
|---|---|---|---|
|
Pattern 1 |
Pattern 2 |
||
|
Diagnosis Condition |
Ignition switch ON |
○ |
○ |
|
Malfunction Status |
Floor side airbag sensor RH malfunction |
○ |
- |
|
Airbag sensor assembly malfunction |
- |
○ |
|
|
Detection Time |
- |
- |
|
|
Number of Trips |
1 trip |
1 trip |
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
|
1. |
CHECK FLOOR SIDE AIRBAG SENSOR RH |
|
(a) Turn the ignition switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the floor side airbag sensor RH with LH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Clear the DTCs stored in memory.
Click here
(f) Turn the ignition switch off.
(g) Turn the ignition switch ON, and wait for at least 60 seconds.
(h) Check for DTCs.
Click here
HINT:
Codes other than DTCs B162A/2A and B163A/3A may be output at this time, but they are not related to this check.
|
Result |
Proceed to |
|---|---|
|
DTC B162A/2A is output. |
A |
|
DTC B163A/3A is output. |
B |
|
DTCs B162A/2A and B163A/3A are not output. |
C |
(i) Turn the ignition switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Return the floor side airbag sensor RH and LH to their original positions and connect the connectors.
| A | |
REPLACE AIRBAG SENSOR ASSEMBLY |
| B | |
REPLACE FLOOR SIDE AIRBAG SENSOR RH |
| C | |
USE SIMULATION METHOD TO CHECK |
Side Airbag Sensor RH Circuit Malfunction (B1620/21)
Rear Airbag Sensor RH Circuit Malfunction (B1630/23)Toyota CH-R Service Manual > Audio And Visual System(for Radio And Display Type): Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast
cannot be Added into Memory
CAUTION / NOTICE / HINT
NOTICE:
Some satellite radio broadcasts require payment. A contract must be made between
a satellite radio company and the user. If the contract expires, it will not be
possible to listen to the broadcast.
PROCEDURE
1.
CHECK SATELLITE RADIO
...
Toyota CH-R Service Manual > Airbag System: Data List / Active Test
DATA LIST / ACTIVE TEST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
disco ...