Toyota CH-R Service Manual: On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. INSPECT DRIVER SEAT BELT WARNING SYSTEM

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.

(a) Turn the ignition switch to ON.

(b) When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.

(c) Lift up the vehicle using a swing arm type lift.

Click here

(d) Start the engine.

(e) When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.

(f) When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

2. INSPECT FRONT PASSENGER SEAT BELT WARNING SYSTEM

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.

(a) Turn the ignition switch to ON.

(b) Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.

(c) Fasten the driver seat belt.

(d) When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.

(e) Lift the vehicle using a swing arm type lift.

Click here

(f) Start the engine.

(g) When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.

3. INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click here

(a) Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.

(b) Lift the vehicle using a swing arm type lift.

Click here

(c) Start the engine.

(d) Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.

(e) After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.

(f) Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.

(g) After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger seat belt is not fastened, and check that the buzzer sounds again.

(h) After the buzzer has stopped, fasten the driver, front passenger seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more, unfasten the driver, front passenger seat belt and check that the buzzer sounds again.

(i) After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.

    Driver Side Seat Belt Warning Light does not Operate
    DESCRIPTION The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (dr ...

    Front Passenger Side Seat Belt Warning Light Malfunction
    DESCRIPTION When the ignition switch is ON, the combination meter assembly monitors the state of the front passenger side seat and the front seat inner belt assembly (front passenger seat) and al ...

    Other materials:

    Toyota CH-R Service Manual > Airbag System: System Description
    SYSTEM DESCRIPTION GENERAL (a) Acceleration sensors and pressure sensors used for the airbag system are installed to various parts on the vehicle and calculate the acceleration rate and pressure of each part during a collision. (b) Depending on the situation, the airbag sensor assembly sends ...

    Toyota CH-R Service Manual > Seat Belt Warning System(w/ Occupant Classification System): How To Proceed With Troubleshooting
    CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the seat belt warning system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT ...

    Toyota C-HR (AX20) 2023-2025 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0116