Toyota CH-R Service Manual: Inspection
INSPECTION
PROCEDURE
1. INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY LH
(a) for TMC Made:
(1) Check the resistance.
- Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-4 - A-5
|
Seat heater temperature 20°C (68°F)
|
2.36 to 2.42 kΩ
|
B-1 - B-2
|
4.46 to 5.34 Ω
|
A-2 - A-6 - B-2
|
Always
|
Below 1 Ω
|
If the result is not as specified, replace the front seat cushion
heater assembly LH.
|
|
*a
|
Component without harness connected
(Front Seat Cushion Heater Assembly LH)
|
|
|
(b) for TMMT Made:
(1) Check the resistance.
- Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-4 - A-5
|
Seat heater temperature 25°C (77°F)
|
4.93 to 5.07 kΩ
|
B-1 - B-2
|
Seat heater temperature 20°C (68°F)
|
2.99 to 3.59 Ω
|
A-2 - A-6 - B-2
|
Always
|
Below 1 Ω
|
If the result is not as specified, replace the front seat cushion
heater assembly LH.
|
|
*a
|
Component without harness connected
(Front Seat Cushion Heater Assembly LH)
|
|
|
2. INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH
(a) for TMC Made:
(1) Check the resistance.
- Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-4 - A-5
|
Seat heater temperature 20°C (68°F)
|
2.36 to 2.42 kΩ
|
B-1 - B-2
|
4.46 to 5.34 Ω
|
A-2 - A-6 - B-2
|
Always
|
Below 1 Ω
|
If the result is not as specified, replace the front seat cushion
heater assembly RH.
|
|
*a
|
Component without harness connected
(Front Seat Cushion Heater Assembly RH)
|
|
|
(b) for TMMT Made:
(1) Check the resistance.
- Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-4 - A-5
|
Seat heater temperature 25°C (77°F)
|
4.93 to 5.07 kΩ
|
B-1 - B-2
|
Seat heater temperature 20°C (68°F)
|
2.99 to 3.59 Ω
|
A-2 - A-6 - B-2
|
Always
|
Below 1 Ω
|
If the result is not as specified, replace the front seat cushion
heater assembly RH.
|
|
*a
|
Component without harness connected
(Front Seat Cushion Heater Assembly RH)
|
|
|
COMPONENTS
ILLUSTRATION
*1
SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
-
-
ILLUSTRATION
*1
FRONT SEAT CUSHION HEA ...
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed, installed, or replaced during th ...
Other materials:
Toyota CH-R Service Manual > Side Airbag Sensor(for Front Door): Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. INSTALL DOOR SIDE AIRBAG SENSOR
(a) Check that the ignition switch off.
(b) Check that the cable is disconnected from the n ...
Toyota CH-R Service Manual > Quarter Garnish: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. INSTALL QUARTER PILLAR COVER SUB-ASSEMBLY
HINT:
When installing a new quarter pillar cover sub-assembly, heat the vehicle b ...