Toyota CH-R Service Manual: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE METER / GAUGE SYSTEM
(a) Customizing with the Techstream.
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch ON.
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Warning or Display.
(5) Select the setting by referring to the table below.
NOTICE:
Be sure to record the current value before customizing.
Display|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
ECO Drive Indicator Zone |
Function to change the ECO Drive Indicator Zone |
ON |
0:OFF,1:ON |
Combination meter assembly |
|
ECO Drive Indicator Light |
Function to change the ECO Drive Indicator light*1 |
ON |
0:OFF,1:ON |
Combination meter assembly |
|
ODO Display Time After IG OFF Setting |
Function to change the ODO display time after the ignition switch is turned off |
30s |
00:30s,01:60s,10:600s,11:OFF |
Combination meter assembly |
|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Flasher Sound Tone Setting |
Function to change the flasher sound tone |
Tone 1 |
00:Tone 1,01:Tone 2,10:Tone 3 |
Combination meter assembly |
|
Lane Change Flashing Times Setting |
Function to change the lane change flashing time |
3 |
000:OFF,001:3,010:4,011:5,100:6,101:7 |
Combination meter assembly |
System Description
SYSTEM DESCRIPTION
INPUT AND OUTPUT SIGNALS OF COMBINATION METER ASSEMBLY
(a) Meter or Gauge
Item
Condition
Input/Output
Communication line
Si ...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the meter / gauge system.
*: Use the Techstream.
PROCEDURE
1.
VEHICL ...
Other materials:
Toyota CH-R Service Manual > Roof Headlining: Installation
INSTALLATION
PROCEDURE
1. INSTALL ROOF HEADLINING
(a) Insert the roof headlining assembly into the cabin from the back door.
Install in this Direction
NOTICE:
Check that the corners of the roof headlining are not folded, twisted
or otherwise deformed ...
Toyota CH-R Service Manual > Blind Spot Monitor System: Operation Check
OPERATION CHECK
HINT:
The blind spot monitor beam axis confirmation is performed to confirm whether
the sensor's beam axis is correct, and perform adjustment of the beam axis by using
reflector.
BLIND SPOT MONITOR BEAM AXIS CONFIRMATION
(a) When performing the blind spot monitor beam axi ...
Toyota C-HR (AX20) 2023-2026 Owner's Manual
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0111