Toyota CH-R Service Manual: How To Proceed With Troubleshooting

Toyota CH-R Service Manual / Door Lock / Power Door Lock Control System / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

Use the following procedure to troubleshoot the power door lock control system.
*: Use the Techstream.

PROCEDURE

1.	VEHICLE BROUGHT TO WORKSHOP

2.	CUSTOMER PROBLEM ANALYSIS CHECK

HINT:

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:

What	Vehicle model, system name
When	Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where	Whether the problem occurs at a specific location
Under what conditions?	Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine has started
How did it happen?	Problem symptoms

PRE-CHECK

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

4.	CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for CAN communication system DTCs.

Click here

Result	Proceed to
CAN DTCs are not output	A
CAN DTCs are output	B

GO TO CAN COMMUNICATION SYSTEM

5.	CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for LIN communication system DTCs.

Click here

Result	Proceed to
LIN DTCs are not output	A
LIN DTCs are output	B

GO TO LIN COMMUNICATION SYSTEM

6.	CHECK FOR DTC (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)*

(a) Clear the DTCs.

Click here

Body Electrical > Master Switch > Clear DTCs

(b) Recheck for DTCs.

Body Electrical > Master Switch > Trouble Codes

Result	Proceed to
DTC B2312 is not output	A
DTC B2312 is output	B

GO TO POWER WINDOW CONTROL SYSTEM

7.	PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result	Proceed to
Fault is not listed in Problem Symptoms Table	A
Fault is listed in Problem Symptoms Table	B

GO TO STEP 9

8.	OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Terminals of ECU

Click here

(b) Data List / Active Test

Click here

(d) Inspection

9.	REPAIR OR REPLACE

10.	CONFIRMATION TEST

END

System Diagram

SYSTEM DIAGRAM Power Door Lock Control System Communication Table Sender Receiver Signal Line Multiplex Network Master Switch Ass ...

Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make sure that ...

Other materials:

Toyota CH-R Service Manual > Occupant Detection Sensor: Inspection
INSPECTION PROCEDURE 1. INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition ...

Toyota CH-R Service Manual > Automatic Headlight Beam Level Control System: Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Automatic Headlight Beam Level Control System DTC No. Detection Item Link B2415 Vehicle Speed Sensor Malfunction B2416 Height Control Sensor Malfunction ...

Toyota CH-R Service Manual: How To Proceed With Troubleshooting

System Diagram

Customize Parameters

Other materials:

Toyota C-HR (AX20) 2023-2026 Owner's Manual

Toyota CH-R Owners Manual

Toyota CH-R Service Manual