Toyota CH-R Service Manual: Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)

Toyota CH-R Service Manual / Window / Glass / Power Window Control System / Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)

DESCRIPTION

If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the power window.

CAUTION / NOTICE / HINT

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

HINT:

This symptom may occur for any of the power windows.

PROCEDURE

1.

PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT

2.

CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION (APPLICABLE LOCATION))

(a) Check that each power window moves when the auto up and down functions of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly are operated.

Click here

OK:

Auto up and down functions are normal (applicable location).

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)
NG

3.

CHECK DOOR GLASS SLIDING MOVEMENT (APPLICABLE LOCATION)

(a) Remove the power window regulator motor assembly and door window regulator sub-assembly.

(b) Install the door glass to the door glass run.

(c) Check that the power window regulator motor assembly and door window regulator sub-assembly operate smoothly.

(d) Check that the door glass slides smoothly when sliding it up by hand.

NOTICE:

Make sure to perform initialization again.

HINT:

Ensure the following:
  • The door glass fits in the door glass run without improper contact or deformation.
  • Foreign matter is not caught in the door glass run.
  • The door glass run is not misaligned.
  • The door glass is not tilted and does not catch on the door glass run.

OK:

Door glass slides smoothly.

Result

Proceed to

OK (Driver door power window)

A

OK (Front passenger door power window)

OK (Rear LH door power window)

B

OK (Rear RH door power window)

NG

C
A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR)

C

FIT DOOR GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS)
    Key-off Operation Function Operates even if Operating Conditions are not Satisfied
    DESCRIPTION When the front doors are closed, each power window regulator motor assembly can be operated for approximately 45 seconds after the ignition switch is turned from ON to off by receivin ...

    Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)
    DESCRIPTION If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the catch protection function may b ...

    Other materials:

    Toyota CH-R Service Manual > Vacuum Warning Switch: Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during vacuum warning switch assembly removal/installation are shown below. Necessary Procedure After Part ...

    Toyota CH-R Service Manual > Smart Key System(for Start Function): Steering Lock Position Signal Circuit Malfunction (B2285)
    DESCRIPTION This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. DTC No. Detection Item ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2025 Copyright www.tochr.net
    0.0117