Toyota CH-R Service Manual: How To Proceed With Troubleshooting

Toyota CH-R Service Manual / Window / Glass / Power Window Control System / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

Use the following procedure to troubleshoot the power window control system.
*: Use the Techstream.

PROCEDURE

1.	VEHICLE BROUGHT TO WORKSHOP

2.	CUSTOMER PROBLEM ANALYSIS

HINT:

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

The following 5 items are important points for problem analysis:

What	Vehicle model, system name
When	Date, time, occurrence frequency
Where	Road conditions
Under what conditions?	Driving conditions, weather conditions
How did it happen?	Problem symptoms

PRE-CHECK

(a) Measure the battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

4.	INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for CAN communication system DTCs.

Click here

Result	Proceed to
CAN DTCs are not output	A
CAN DTCs are output	B

GO TO CAN COMMUNICATION SYSTEM

5.	INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for LIN communication system DTCs.

Click here

Result	Proceed to
LIN DTCs are not output	A
LIN DTCs are output	B

GO TO LIN COMMUNICATION SYSTEM

6.	CHECK FOR DTC*

(a) Check for DTCs and make a note of any codes that are output.

Click here

Body Electrical > Master Switch > Trouble Codes Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble Codes

(b) Clear the DTCs.

Body Electrical > Master Switch > Clear DTCs Body Electrical > D-Door Motor > Clear DTCs Body Electrical > P-Door Motor > Clear DTCs Body Electrical > RL-Door Motor > Clear DTCs Body Electrical > RR-Door Motor > Clear DTCs

Result	Proceed to
DTCs are not output	A
DTCs are output	B

GO TO DIAGNOSTIC TROUBLE CODE CHART

7.	PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result	Proceed to
Fault is not listed in problem symptoms table	A
Fault is listed in problem symptoms table	B

GO TO STEP 9

8.	OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Terminals of ECU

Click here

(d) Fail-safe Chart

Click here

(e) Inspection

9.	ADJUST, REPAIR OR REPLACE

(a) Check if any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.

Result	Proceed to
Any of the door window regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled.	A
The door window regulator sub-assemblies, power window regulator motor assemblies, door glass and door glass runs have not been removed and reinstalled.	B

GO TO STEP 11

10.	INITIALIZE POWER WINDOW CONTROL SYSTEM

(a) If any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, perform "Initialize Power Window Control System" for the applicable door glass.

Click here

11.	CONFIRMATION TEST

END

System Description

SYSTEM DESCRIPTION POWER WINDOW CONTROL SYSTEM DESCRIPTION (a) The power window control system controls the power window operation using the power window regulator motor assemblies. The main contr ...

Operation Check

OPERATION CHECK CHECK WINDOW LOCK FUNCTION HINT: Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in). (a) Turn ...

Other materials:

Toyota CH-R Service Manual > Blower Unit(for Denso Made): Reassembly
REASSEMBLY PROCEDURE 1. INSTALL NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (a) Connect the 2 links of the blower assembly to the 2 plates of the No. 1 blower damper servo sub-assembly as shown in the illustration. ...

Toyota CH-R Service Manual > Smart Key System(for Entry Function): Front Passenger Side Door Entry Unlock Function does not Operate
DESCRIPTION If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the unlock sensor (connection betwee ...

Toyota CH-R Service Manual: How To Proceed With Troubleshooting

System Description

Operation Check

Other materials:

Toyota C-HR (AX20) 2023-2026 Owner's Manual

Toyota CH-R Owners Manual

Toyota CH-R Service Manual