Toyota CH-R Service Manual: Data List / Active Test

Toyota CH-R Service Manual / Lighting (ext) / Automatic Headlight Beam Level Control System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / HL AutoLeveling / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > HL AutoLeveling > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Front Window Washer Switch	Front window washer switch signal	ON or OFF	ON: Front window washer switch on OFF: Front window washer switch off	-
Headlight Low Beam State	Low beam headlight state	ON or OFF	ON: Low beam headlights on OFF: Low beam headlights off	-
Headlight High Beam State	High beam headlight state	ON or OFF	ON: High beam headlights on OFF: High beam headlights off	-
DRL Operating State	DRL state	ON or OFF	ON: DRL on OFF: DRL off	-
Daylight Operating State	Daytime running light state	ON or OFF	ON: Daytime running lights on OFF: Daytime running lights off	-
Clearance Light State	Clearance light state	ON or OFF	ON: Clearance lights on OFF: Clearance lights off	-
+B	Headlight ECU sub-assembly LH IG power supply voltage value	0 to 19.75 V	11.00 to 14.00 V	-
Height Sens Pw Supply Val	Rear height control sensor sub-assembly LH power supply value	0 to 5.00 V	4.61 to 5.00 V	-
Rr Height Sens Signal Val	Rear height control sensor sub-assembly LH signal value	0 to 5.00 V	0.50 to 4.50 V	Value changes according to vehicle height
Front Right Wheel Speed Value	Front right wheel speed	0.00 to 260.00 km/h (162.00 mph)	Vehicle stopped: 0 km/h (0 mph)	-
Front Left Wheel Speed Value	Front left wheel speed	0.00 to 260.00 km/h (162.00 mph)	Vehicle stopped: 0 km/h (0 mph)	-
Vehicle Speed	Vehicle speed	0.00 to 260.00 km/h (162.00 mph)	Vehicle stopped: 0 km/h (0 mph)	-
Rear Height Adjust Value	Rear height adjustment off set value	0 to 1023	Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed)	-
Rear Height Adjust Valid Flag	Rear height adjustment range	Valid or Invalid	Valid: Rear height control sensor sub-assembly LH value within normal range Invalid: Rear height control sensor sub-assembly LH value out of normal range	-
Init Writing Count	Number of times initialization performed	0 to 255	Number of times initialization performed	-
Sensor Initialization Hist	Sensor initialization history	not comp, 10%, 25%, 50%, 75%, 100% or completed	not comp: Headlight ECU sub-assembly LH not initialized after replacing. 10%: Initialization completed when fuel tank was 10% full 25%: Initialization completed when fuel tank was 25% full 50%: Initialization completed when fuel tank was 50% full 75%: Initialization completed when fuel tank was 75% full 100%: Initialization completed when fuel tank was 100% full completed: ECU not replaced and ECU has not been initialized at workshop.	-
+B Voltage Value	Headlight ECU sub-assembly LH +B power supply voltage value	0 to 19.75 V	11 to 14 V	-
Leveling Motor Target Position	Headlight leveling motor target position	0 to 102.3 %	10 to 90 %	-
Number Of Trouble Codes	Number of trouble codes	0 to 255	Number of stored DTCs displayed	-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > HL AutoLeveling > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Drive The Leveling Motor	Headlight leveling motor upward or downward operation	Stop/Down/Up	Perform the Active Test with the engine started and vehicle stopped
Headlight Leveling Indicator	"Headlight System Malfunction Visit Your Dealer" display	ON or OFF	-

Freeze Frame Data

FREEZE FRAME DATA FREEZE FRAME DATA (a) Whenever an automatic headlight beam level control system DTC is stored, the headlight ECU sub-assembly LH stores the current vehicle state as freeze frame ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Automatic Headlight Beam Level Control System DTC No. Detection Item Link B2415 Vehicle Speed Sensor Malfun ...

Other materials:

Toyota CH-R Owners Manual > Tire information: Glossary of tire terminology
Tire related term Meaning Cold tire inflation pressure Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition Maximum inflation pressure The maximum cold inflated pressur ...

Toyota CH-R Service Manual > Automatic Headlight Beam Level Control System: Headlight Beam Level Control Motor LH Malfunction (B2417,B2418)
DESCRIPTION The headlight unit (headlight leveling motor) receives a signal from the headlight control ECU sub-assembly to operate. The headlight control ECU sub-assembly receives a signal indicating the operating conditions of the headlight unit (headlight leveling motor). DTC No ...