Toyota CH-R Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Blind Spot Monitor Master > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Main Switch |
State of the Blind spot monitor system |
OFF or ON |
OFF: Blind spot monitor system off ON: Blind spot monitor system on |
- |
|
RCTA Switch Status |
State of RCTA function |
OFF or ON |
OFF: RCTA function off OFF: RCTA function on |
- |
|
Warning Indicator Turning on(Master) |
State of the outer rear view mirror indicator LH turning on |
OFF or ON |
|
- |
|
Warning Indicator Flashing(Master) |
State of the outer rear view mirror indicator LH flashing |
OFF or ON |
OFF: Any state except "ON" ON: Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch on |
- |
|
Main Switch Indicator Status |
State of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) |
OFF or ON |
OFF: Indicator not illuminated ON: Indicator illuminated |
- |
|
Warning Indicator Input Circuit Voltage |
Outer rear view mirror indicator voltage |
Min.: 0 V, Max.: 25.5 V |
Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V |
- |
|
Warning Indicator Input Circuit Current |
Outer rear view mirror indicator current |
Min.: 0 mA, Max.: 255 mA |
Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA |
- |
|
Turn Switch State |
State of the turn signal switch |
Left ON, Right ON or OFF |
Left ON: Left turn signal switch on Right ON: Right turn signal switch on OFF: Turn signal switch off |
- |
|
Reverse (Only for AT/CVT) |
State of the shift position R signal |
OFF or ON |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
|
Vehicle Speed |
Vehicle speed signal |
Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) |
Vehicle stopped: 0 km/h (0 mph) |
- |
|
Steering Angle |
Steering angle sensor |
Min.: -3072 deg, Max.: 3070.5 deg |
Left turn: Increases Right turn: Decreases |
- |
|
Power Supply Voltage |
Power supply voltage |
Min.: 0 V, Max.: 49.951 V |
Ignition switch to ON: 11 to 14 V |
- |
|
Indicator Light Control State |
Outer rear view mirror indicator dimming state |
Dim OFF or Dim ON |
Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
|
HV Flag |
Hybrid vehicle |
OFF or ON |
OFF: Non-hybrid vehicle ON: Hybrid vehicle |
- |
|
VGRS Flag |
VGRS installed |
OFF or ON |
OFF: VGRS not installed ON: VGRS installed |
- |
|
Main SW Inspection Completeness Flag |
Completion of inspection for blind spot monitor main switch |
Incompl or Compl |
Incompl: Inspection not completed Compl: Inspection completed |
- |
|
Beam Axis Inspection Completeness Flag |
Completion of beam axis adjustment |
Incompl or Compl |
Incompl: Adjustment not completed Compl: Adjustment completed |
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished |
|
Destination Undefined Flag |
Destination determination |
Unfixed or Fixed |
Unfixed: Sensor destination information not determined Fixed: Sensor destination information determined according to CAN destination information |
- |
|
Angle Adjustment by Auto Alignment |
Angle adjusted using auto alignment |
Min.: Under -180 deg, Max.: Over 180 deg |
Angle adjusted using auto alignment is displayed |
- |
|
RCTA Equipped Information |
RCTA installed |
OFF or ON |
OFF: RCTA not installed ON: RCTA installed |
- |
|
Master Side RCTA Function |
Switches the RCTA function on and off |
OFF or ON |
ON: RCTA function on OFF: RCTA function off |
- |
|
Mirror LED Control Frequency |
Frequency of the outer rear view mirror indicator on the outer mirror when blinking |
Min.: 1500 Hz, Max.: 2400 Hz |
Always: 2000 Hz |
- |
|
Setting of Warning Indicator Current (Dim OFF) |
Set current of the outer rear view mirror indicator when not dimmed |
Min.: 0 mA, Max.: 100 mA |
Always: 0 to 100 mA |
- |
|
Setting of Warning Indicator Current (Dim ON) |
Set current of the outer rear view mirror indicator when dimmed |
Min.: 0 mA, Max.: 100 mA |
Always: 0 to 100 mA |
- |
|
Mirror LED Duty Ratio (Blinking) |
Duty ratio of the outer rear view mirror indicator when blinking |
Min.: 0%, Max.: 100% |
Always: 50% |
- |
|
Yaw Rate Sensor |
Yaw rate sensor |
Min.: Under -125 deg/s, Max.: 124.612 deg/s |
Turning right: -125 to 0 deg/s Turning left: 0 to 124.612 deg/s |
- |
|
BSM Mirror Indicator Brightness |
Brightness of the indicators in the outer rear view mirror assemblies |
Dark or Bright |
Dark: Outer mirror indicator brightness low Bright: Outer mirror indicator brightness high |
- |
|
Number of DTC |
Number of DTCs |
Min.: 0, Max.: 255 |
When system is normal: 0 When a malfunction is detected: More than 0 |
- |
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Warning Indicator Turning on(Slave) |
State of the outer rear view mirror indicator RH turning on |
OFF or ON |
|
- |
|
Warning Indicator Flashing(Slave) |
State of the outer rear view mirror indicator RH flashing |
OFF or ON |
OFF: Any state except "ON" ON: Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch on |
- |
|
Buzzer Sound Status |
State of the RCTA buzzer (blind spot monitor buzzer) |
OFF or ON |
OFF: Buzzer not sounding ON: Buzzer sounding |
- |
|
Warning Indicator Input Circuit Voltage |
Outer rear view mirror indicator voltage |
Min.: 0 V, Max.: 25.5 V |
Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V |
- |
|
Warning Indicator Input Circuit Current |
Outer rear view mirror indicator current |
Min.: 0 mA, Max.: 255 mA |
Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA |
- |
|
Buzzer Input Circuit Voltage |
RCTA buzzer (blind spot monitor buzzer) voltage |
Min.: 0 V, Max.: 25.5 V |
Buzzer not sounding: 11 to 14 V Buzzer sounding: Alternating between 0 to 14 V |
- |
|
Turn Switch State |
State of the turn signal switch |
Left ON, Right ON or OFF |
Left ON: Left turn signal switch on Right ON: Right turn signal switch on OFF: Turn signal switch off |
- |
|
Reverse (Only for AT/CVT) |
State of the shift position R signal |
OFF or ON |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
|
Reverse (Only for MT) |
State of the shift position R signal |
OFF or ON |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
|
Vehicle Speed |
Vehicle speed signal |
Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) |
Vehicle stopped: 0 km/h (0 mph) |
- |
|
Steering Angle |
Steering angle sensor |
Min.: -3072 deg, Max.: 3070.5 deg |
Left turn: Increases Right turn: Decreases |
- |
|
Power Supply Voltage |
Power supply voltage |
Min.: 0 V, Max.: 49.951 V |
Ignition switch to ON: 11 to 14 V |
- |
|
Indicator Light Control State |
Outer rear view mirror indicator dimming state |
Dim OFF or Dim ON |
Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
|
HV Flag |
Hybrid vehicle |
OFF or ON |
OFF: Non-hybrid vehicle ON: Hybrid vehicle |
- |
|
VGRS Flag |
VGRS installed |
OFF or ON |
OFF: VGRS not installed ON: VGRS installed |
- |
|
Beam Axis Inspection Completeness Flag |
Completion of beam axis adjustment |
Incompl or Compl |
Incompl: Adjustment not completed Compl: Adjustment completed |
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished |
|
Destination Undefined Flag |
Destination determination |
Unfixed or Fixed |
Unfixed: Sensor destination information not determined |
- |
|
Angle Adjustment by Auto Alignment |
Angle adjusted using auto alignment |
Min.: Under -180 deg, Max.: Over 180 deg |
Angle adjusted using auto alignment is displayed |
- |
|
RCTA Equipped Information |
RCTA installed |
OFF or ON |
OFF: RCTA not installed ON: RCTA installed |
- |
|
Mirror LED Control Frequency |
Frequency of the outer rear view mirror indicator on the outer mirror when blinking |
Min.: 1500 Hz, Max.: 2400 Hz |
Always: 2000 Hz |
- |
|
Setting of Warning Indicator Current (Dim OFF) |
Set current of the outer rear view mirror indicator when not dimmed |
Min.: 0 mA, Max.: 100 mA |
Always: 0 to 100 mA |
- |
|
Setting of Warning Indicator Current (Dim ON) |
Set current of the outer rear view mirror indicator when dimmed |
Min.: 0 mA, Max.: 100 mA |
Always: 0 to 100 mA |
- |
|
Mirror LED Duty Ratio (Blinking) |
Duty ratio of the outer rear view mirror indicator when blinking |
Min.: 0%, Max.: 100% |
Always: 50% |
- |
|
Buzzer Control Frequency |
Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding |
Min.: 1000 Hz, Max.: 2400 Hz |
Always: 2000 Hz |
- |
|
Yaw Rate Sensor |
Yaw rate sensor |
Min.: Under -125 deg/s, Max.: 124.612 deg/s |
Turning right: -125 to 0 deg/s Turning left: 0 to 124.612 deg/s |
- |
|
BSM Buzzer Volume Adjust |
Volume of the RCTA buzzer (blind spot monitor buzzer) |
Low, Medium or High |
Low: Buzzer volume less than that of medium Medium: Default buzzer volume High: Buzzer volume more than that of medium |
- |
|
Number of DTC |
Number of DTCs |
Min.: 0, Max.: 255 |
When system is normal: 0 When a malfunction is detected: More than 0 |
- |
Freeze Frame Data
FREEZE FRAME DATA
FREEZE FRAME DATA
(a) Whenever DTCs are detected, the blind spot monitor sensor stores the current
vehicle (sensor) state as freeze frame data.
CHECK FREEZE FRAME DATA
(a) Conn ...
Master Module Horizontal Axis Misalignment (C1AC1)
DESCRIPTION
This DTC is stored when the angle of the blind spot monitor sensor LH (Master)
deviates more than the allowable range from the horizontal axis.
HINT:
If a drum tester such as ...
Other materials:
Toyota CH-R Service Manual > Lin Communication System: Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
LIN Communication System
DTC No.
Detection Item
Link
B1206
P/W Master Switch Communication Stop
B1249
Double Locking ECU Communication Stop
...
Toyota CH-R Service Manual > Audio And Visual System(for Radio And Display Type): USB Device Malfunction (B1585)
DESCRIPTION
This DTC is stored when a malfunction occurs in a connected device.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
B1585
USB Device Malfunction
USB Device Malfunction
Non mass- ...
Toyota CH-R Owners Manual
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Toyota CH-R Service Manual
- Introduction
- Maintenance
- Audio / Video
- Cellular Communication
- Navigation / Multi Info Display
- Park Assist / Monitoring
- Brake (front)
- Brake (rear)
- Brake Control / Dynamic Control Systems
- Brake System (other)
- Parking Brake
- Axle And Differential
- Drive Shaft / Propeller Shaft
- K114 Cvt
- 3zr-fae Battery / Charging
- Networking
- Power Distribution
- Power Assist Systems
- Steering Column
- Steering Gear / Linkage
- Alignment / Handling Diagnosis
- Front Suspension
- Rear Suspension
- Tire / Wheel
- Tire Pressure Monitoring
- Door / Hatch
- Exterior Panels / Trim
- Horn
- Lighting (ext)
- Mirror (ext)
- Window / Glass
- Wiper / Washer
- Door Lock
- Heating / Air Conditioning
- Interior Panels / Trim
- Lighting (int)
- Meter / Gauge / Display
- Mirror (int)
- Power Outlets (int)
- Pre-collision
- Seat
- Seat Belt
- Supplemental Restraint Systems
- Theft Deterrent / Keyless Entry
0.0132