Toyota CH-R Service Manual: Problem Symptoms Table

Toyota CH-R Service Manual / Cellular Communication / Toyota Entune System / Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

NOTICE:

The following may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with a new one.
- A communication malfunction DTC is stored.
- The radio and display receiver assembly does not operate normally.
If the DCM (telematics transceiver) has been replaced, perform the DCM Activation procedure.
Click here

HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.

Entune On-screen Message

Symptom	Suspected Area	Link
A message is temporarily displayed indicating to try again after waiting for a while because the lines are busy	This is caused when there is a problem with the radio wave signal conditions or when the call center is busy. This is not a malfunction. (Inform the customer that this is not a malfunction and ask them to use the system as is.)	-
	Contact the call center	-
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
A message is displayed indicating to try again after waiting for a while because information cannot be retrieved due to a busy line, etc.	Wait for a while and perform the operation again in a different location	-
	Contact the call center	-
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
A message is displayed indicating to try again because information was not able to be retrieved	Contact the call center	-
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
A message is displayed indicating to try again after waiting for a while because communication is being setup	The system is trying to detect the DCM (telematics transceiver). Wait for a while and perform the operation again	-
	Contact the call center	-
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
A message is displayed indicating to move the vehicle into a communication service area as it is outside a service area	Wait for a while and perform the operation again in a different location (Within the communication service area)	-
	Contact the call center	-
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
A message is displayed indicating to move the vehicle to where a GPS signal can be received because the time data is old	Proceed to "GPS Mark is not Displayed"
	If the GPS mark is displayed, wait for a while and perform the operation again in a different location	-
	If the problem symptom is duplicated, replace the radio and display receiver assembly
A message is displayed indicating that this service is not available now	Explain to the customer that the service is currently not available.	-
A message is displayed indicating to ask the dealer about applying for the service as it is necessary to create a contract before using the service	Confirm the status of the paid service contract.	-
	Contact the call center	-

Destination Function

Symptom	Suspected Area	Link
Cannot contact call center when Call Dest. Assist is selected on Destination Assist Connect screen	Contact Telematics Service Provider to inquire about network status	-
	Proceed to "UNABLE TO CONNECT TO CALL CENTER"
	Proceed to "DCM Data Signal Circuit between Navigation ECU and DCM"
	Radio and display receiver assembly
	DCM (Telematics Transceiver)
Other caller's voice volume cannot be adjusted using the Destination Assist Connect screen	Radio and display receiver assembly

Dynamic Voice Recognition

Symptom	Suspected Area	Link
Does not recognize voice commands performed to contact support center	Check if the Toyota Entune System service is available	-
	Check if the normal voice recognition function is operating correctly
	Proceed to "Does not Recognize Voice Commands Performed to Contact Support Center"
Dynamic voice recognition function does not operate	Check if the Toyota Entune System service is available	-
Dynamic voice recognition function does not operate	Proceed to "UNABLE TO CONNECT TO CALL CENTER"

Toyota Entune App Suite Connect Function

Symptom	Suspected Area	Link
Toyota Entune App Suite Connect function error message is displayed on the screen	Follow on screen instructions	-
	Proceed to "Confirm Cellular Phone Functionality"
	Proceed to "Confirm Vehicle Headunit Functionality"
	Proceed to "App Suite Connect Reset Procedure" in Operation Check
	Radio and display receiver assembly
Toyota Entune App Suite Connect and services are not operating as expected	Proceed to "Confirm Cellular Phone Functionality"
	Proceed to "Confirm Vehicle Headunit Functionality"
	Proceed to "App Suite Connect Reset Procedure" in Operation Check
	Radio and display receiver assembly
Toyota Entune App Suite Connect voice recognition is not possible (Voice recognition on the audio and visual system is normal)	Proceed to "Confirm Cellular Phone Functionality"
	Proceed to "Confirm Vehicle Headunit Functionality"
	Proceed to "App Suite Connect Reset Procedure" in Operation Check
	Radio and display receiver assembly
Sound quality of Toyota Entune App Suite Connect function is poor	Check that cellular phone handset volume is turned up	-
	Check that adequate signal is maintained while the vehicle is being driven	-
	Proceed to "Confirm Cellular Phone Functionality"
	Proceed to "Confirm Vehicle Headunit Functionality"
	Proceed to "App Suite Connect Reset Procedure" in Operation Check
	Radio and display receiver assembly

Operation Check

OPERATION CHECK TOYOTA ENTUNE APP SUITE CONNECT RESET PROCEDURE (a) Duplicate the problem symptom. (b) Check for DTCs and repair the systems for which any DTCs are output. Click here (c) Chec ...

Terminals Of Ecu

TERMINALS OF ECU DCM (TELEMATICS TRANSCEIVER) Click here RADIO AND DISPLAY RECEIVER ASSEMBLY w/o Navigation System: Click here w/ Navigation System: Click here ...

Other materials:

Toyota CH-R Service Manual > Automatic High Beam System: Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the ...

Toyota CH-R Service Manual > Brake Pedal: Components
COMPONENTS ILLUSTRATION *1 BRAKE PEDAL PAD *2 BRAKE PEDAL RETURN SPRING *3 BRAKE PEDAL SUPPORT ASSEMBLY *4 PUSH ROD PIN *5 STOP LIGHT SWITCH MOUNTING ADJUSTER *6 ...

Toyota CH-R Service Manual: Problem Symptoms Table

Operation Check

Terminals Of Ecu

Other materials:

Toyota CH-R Owners Manual

Toyota CH-R Service Manual