Toyota CH-R Service Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Pre-Collision 2 > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Turn Light RH

Turn signal switch (right) status

ON or OFF

ON: Turn signal switch (right) on

OFF: Turn signal switch (right) off

-

Turn Light LH

Turn signal switch (left) status

ON or OFF

ON: Turn signal switch (left) on

OFF: Turn signal switch (left) off

-

PCS OFF Switch

Pre-collision system on/off status

ON or OFF

ON: Pre-collision system on

OFF: Pre-collision system off

-

PCS Indicator

"Pre-Collision System Malfunction Visit Your Dealer" display request signal

ON or OFF

ON: "Pre-Collision System Malfunction Visit Your Dealer" display requested

OFF: "Pre-Collision System Malfunction Visit Your Dealer" display not requested

-

PCS Disabled Indicator

"Pre-Collision System Unavailable" display request signal

ON or OFF

ON: "Pre-Collision System Unavailable" display requested

OFF: "Pre-Collision System Unavailable" display not requested

-

Pre-Collision Safety Warning Buz

Pre-collision system warning buzzer

Valid or Inval

Valid: Pre-collision system warning buzzer operation possible

Inval: Pre-collision system warning buzzer operation not possible

-

Pre-Collision Brake

Pre-collision brake function

Valid or Inval

Valid: Pre-collision brake operation possible

Inval: Pre-collision brake operation not possible

-

PBA Start

Pre-collision brake assist activation signal

OFF, Standby, Assist Lv1 or Assist Lv2

OFF: Pre-collision brake assist not operating

Standby: Brake pedal not depressed during pre-collision brake assist operation

Assist Lv1: Brake pedal depressed during pre-collision brake assist operation

Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation

Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)

Brake Assist Standby

-

-

-

This item is displayed on the Techstream but is not used.

Pre-Collision Brake Control

Pre-collision brake operational status

ON or OFF

ON: Pre-collision brake operating

OFF: Pre-collision brake not operating

-

AVS Start

-

-

-

This item is displayed on the Techstream but is not used.

VGRS Start

-

-

-

This item is displayed on the Techstream but is not used.

PBA Control

Pre-collision brake assist operational status

Valid or Invalid

Valid: Pre-collision brake assist control operation possible

Invalid: Pre-collision brake assist control operation not possible

-

Pre-Collision Safety Brake Ind

Pre-collision system alarm warning message status

ON or OFF

ON: Displayed

OFF: Not displayed

"BRAKE!" is displayed

PCS Collision Alarm Buzzer

Pre-collision city buzzer status

ON or OFF

ON: Pre-collision city buzzer sounding

OFF: Pre-collision city buzzer not sounding

-

Front Radar-Dirt History

Millimeter wave radar sensor assembly dirt history

ON or OFF

ON: History of excessive dirt

OFF: No history of excessive dirt

-

Front Radar-Environment Hist

Millimeter wave radar sensor assembly environment signal

Good or Bad

Good: Millimeter wave radar sensor assembly environment good

Bad: Millimeter wave radar sensor assembly environment bad

-

Front Radar-Temperature Malfunction History

Millimeter wave radar sensor assembly abnormal temperature history

ON or OFF

ON: History of abnormal temperature

OFF: No history of abnormal temperature

-

Front Radar-Low Voltage History

Millimeter wave radar sensor assembly low voltage history

ON or OFF

ON: History of low voltage

OFF: No history of low voltage

If the engine starts 1 second or more after the ignition switch was turned to ON (IG), this item may change to ON.

Front Recognition Camera-Blockage History

Forward recognition camera obstruction history

ON or OFF

ON: History of being obstructed

OFF: No history of being obstructed

-

Front Recognition Camera-Malfunction History

Forward recognition camera system unavailable history

ON or OFF

ON: History of unavailable

OFF: No history of unavailable

-

Destination Variation No

Destination country for millimeter wave radar sensor assembly

0 or Not Available

Not Available

-

Control Mode

ECU control mode status

Normal or Check Mode

Normal: Normal operation

Check Mode: Operating in Control Mode

-

PCS Operation State Retention Setting

PCS Operation State Retention Setting customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 1

PCS Alarm Activation Distance Retention Setting 1 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 2

PCS Alarm Activation Distance Retention Setting 2 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

PCS Alarm Activation Distance Retention Setting 3

PCS Alarm Activation Distance Retention Setting 3 customize setting

ON or OFF

ON: Customize setting set to ON

OFF: Customize setting set to OFF

-

The Number of DTCs

Number of past trouble codes

min: 0, max: 255

Number of DTCs will be displayed

-

(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.

(g) Read the Data List according to the display on the Techstream.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Stop Light Relay Output

Stop light switch assembly output

ON or OFF

ON: Stop light switch assembly output on (Stop lights on)

OFF: Stop light switch assembly output off (Stop lights off)

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Pre-Collision 2 > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PCS Collision Alarm Buzzer

Pre-collision city buzzer

ON / OFF

Test possible with ignition switch to ON

Vehicle condition: Vehicle stopped

(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.

(g) Perform the Active Test according to the display on the Techstream.

Chassis > ABS/VSC/TRAC/EPB > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Stop Light Relay

Stop light switch assembly

Stop light switch assembly ON/OFF

Stop lights come on

Vehicle condition: Vehicle stopped

(h) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(i) Perform the Active Test according to the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Indicat. Precrash

PCS warning light

ON / OFF

-

    Freeze Frame Data
    FREEZE FRAME DATA DESCRIPTION (a) When a pre-collision system DTC is stored, the millimeter wave radar sensor assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data. CHECK ...

    Fail-safe Chart
    FAIL-SAFE CHART FAIL-SAFE FUNCTION (a) When a malfunction occurs in the pre-collision system, a message will be displayed on the multi-information display and the pre-collision system will be di ...

    Other materials:

    Toyota CH-R Service Manual > Maintenance: Tire And Wheel
    Components COMPONENTS ILLUSTRATION *A for Steel Wheel - - *1 WHEEL ASSEMBLY *2 WHEEL CAP *3 AXLE HUB NUT - - Tightening tor ...

    Toyota CH-R Service Manual > Audio And Visual System(for Radio And Display Type): Diagnostic Trouble Code Chart
    DIAGNOSTIC TROUBLE CODE CHART Audio and Visual System DTC No. Detection Item Link B1324 Lost Communication with Meter B1551 HD Radio Tuner Malfunction B ...

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2024 Copyright www.tochr.net
    0.0137